Publicité
Les langues disponibles
Les langues disponibles
1. Use a screwdriver to block the rotation of
the blade plate (11). Do this by inserting the
screwdriver through the holes in the blade
plate (11) and the protective ridge.
2. Undo the fastening screws.
3. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
4. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which have accumulated. At the start of each
season, ensure that you check the condition of
the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
7.2.2 Software update
If you want to update the software, copy the new
software to an empty USB stick (format the USB
stick fi rst if necessary). Make sure that the battery
is fully charged before you carry out the following
steps.
1. With the robot lawn mower switched on, place
it in the mowing area. The robot lawn mower
must not be in the charging station (19) during
the software update.
2. Connect a USB stick to the USB connection
as shown (Fig. 11).
3.1 The robot lawn mower will now install the two
fi les one after the other. Alternatively the fi les
can be updated one at a time. In this case you
must fi rst switch off the robot lawn mower with
the main switch (OFF).
3.2 System update (example of fi le name:
CMK_3100.1.2.3.4.bin): Press the button "4H"
for the mowing time setting (60) and simulta-
neously switch on the robot lawn mower with
the main switch (7) (ON).
3.3 Camera update (example of fi le name:
Camera_1.2.3.4.bin): Press the button "10H"
for the mowing time setting (60) and simulta-
neously switch on the robot lawn mower with
the main switch (7) (ON).
4. The time LEDs (50) will fl ash during the up-
date process.
5. When fi nished, the robot lawn mower will emit
a continuous beep sound. If successful, all 4
time LEDs (50) will light up. If uncompleted, all
4 time LEDs (50) will go out and you will need
to repeat the software update.
6. Pull out the USB stick and restart the robot
lawn mower with the main switch (7).
GB
7.2.3 Repairing the guide cable
First disconnect the charging station (19) from
the power supply. If the guide cable (24) has
been severed at any point, use the supplied cable
connectors (25) to repair it. To do so, insert both
ends of the severed guide cable (24) into the
cable connector (25) and squeeze it with the help
of a pair of pliers. Connect the power plug to the
socket outlet. Finally, check the LED display (19a)
on the charging station (19) to see if the function
is working.
7.3 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For the latest prices and information go to www.
Einhell-Service.com
Replacement blades Art. No.: 34.140.20
8. Storage
Fully charge the battery (A) before putting it into
storage over winter and switch off the robot lawn
mower at the main switch (7) (OFF). Take the
battery (A) out of the equipment. Disconnect the
power supply unit (20) from the power supply and
the charging station (19).
The guide cable (24) can be left outdoors over
winter. However, make sure that the connections
are protected against corrosion. To do so, discon-
nect the connections of the guide cable (24) from
the charging station (19).
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30°C. Store the equipment
in its original packaging.
- 55 -
Publicité
