Publicité
Les langues disponibles
Les langues disponibles
5.11 Securing the charging station
Once the robot lawn mower is working properly
and a suitable position for the charging station
(19) has been found, the charging station (19)
must be fi xed in place using the fastening screws
(21). Use the hexagon key (22) to secure the fas-
tening screws (21) fully in the ground (Fig. 7).
5.12 Battery charge level indicator
Press the button for the battery charge level indi-
cator. The battery charge level indicator indicates
the charge state of the battery by means of 3
LEDs (Fig. 12b).
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the battery has undergone exhaustive di-
scharge and is defective. Remove the battery from
the tool. Never use or charge a defective battery.
Important!
When using a multi-Ah pack (e.g. 4-6Ah), always
set the higher capacity. Thanks to the gentle
charging and discharging of the robot lawn mower
there is no need to use the lower capacity in order
to extend the working life.
5.13 Charging the battery with the charger
In normal operation the battery (A) of the robot
lawn mower is charged via the charging station
(19). For independent use of the battery (A) from
the Power-X-Change series it can also be charged
in the external Power-X-Charger. Important! –
Depending on the model of your robot lawn mo-
wer, it might not come complete with the battery
charger (B).
1. Check that your mains voltage is the same
as that marked on the rating plate. Insert the
power plug of the charger (B) into the socket
outlet. The green LED will begin to blink.
2. Insert the battery (A) into the battery charger
(B) (Fig. 12a).
3. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
GB
display on the charger.
The battery can become a little warm during the
charging. This is normal.
If the battery pack fails to charge, check:
•
Is there voltage at the power socket?
•
Is there good contact at the charging con-
tacts?
If the battery pack still fails to charge, please send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6. Operation
6.1 Main switch
The robot lawn mower is equipped with a main
switch (7). Use the main switch (7) to switch the
robot lawn mower on (ON) and off (OFF) (Fig. 8).
Once the robot lawn mower has been switched on
it will be locked by the PIN.
6.2 Control panel
The control panel (2) can be used to make the
settings on your robot lawn mower. The integrated
LED display informs you about the status of your
robot lawn mower. Familiarize yourself with the
controller and the available options.
Explanation of the LEDs on the control panel
(Fig. 9a)
50. Time LEDs: Display of the daily mowing time
51. Lock LED: Display of the button lock
52. Status LED: Status display of the robot lawn
- 51 -
Publicité
