EINHELL FREELEXO CAM Instructions D'origine page 54

the display cover (25).
•
By unlocking the robot lawn mower and pres-
sing the button „HOME" (61) in order to send
the robot lawn mower back into the station.
Close the display cover (25).
•
By unlocking the robot lawn mower and clo-
sing the display cover (25) within 5 seconds.
•
By unlocking the robot lawn mower and pres-
sing the lock button (62).
7. Cleaning, maintenance and
ordering spare parts
Danger!
The equipment must be disconnected from the
power supply (pull out the power plug and switch
off the equipment by the main switch (7) (OFF)
(Fig. 8)) prior to performing any cleaning and
maintenance work. Also take the battery (A) out of
the robot lawn mower (Fig. 3b).
Caution! Wear working gloves!
7.1 Cleaning the tool
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow over it with compressed air at
low pressure.
•
Do not clean the robot lawn mower with run-
ning water, particularly at high pressure.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use cleaning
agents or solvents; these might be aggressive
to the plastic parts in the equipment. Ensure
that no water can get into the interior of the
equipment.
•
For best results, clean the robot lawn mower
with a brush or rag.
•
Check the freedom of movement of the bla-
des (10) and the blade plate (11).
•
Use cleaning product for metal or very fine
abrasive paper to clean the charging contacts
on the robot lawn mower (1) and the charging
station (19). Clean them in order ensure effici-
ent charging.
7.2 Maintenance
•
Check the lens of the camera unit (15) regu-
larly for signs of dirt and clean if necessary.
The lens is likely to become dirty particularly
when it rains. Do not use any aggressive
cleaning agents or solvents.
•
Worn or damaged blades (10) and their faste-
GB
ning screws must always be replaced as a set.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your robot lawn mower in good
condition not only ensures a long lifespan
and high performance, but also enables the
equipment to thoroughly cut your grass with
minimal effort.
•
The blades (10) are subject to more wear and
tear than any other component. Therefore,
routinely check the condition of the blades
(10) and make sure that they are tightly fas-
tened. An excessively vibrating robot lawn
mower can indicate that the blades (10) are
damaged or have become deformed from
striking an object. If the blades (10) are worn
or damaged, they must be replaced immedia-
tely.
•
Check the appearance of the cut lawn at regu-
lar intervals. The grass will not be cleanly cut if
the blades are not sharp. This can result in the
surface of the lawn drying out easily and tur-
ning brown. It is important therefore to change
the blades regularly in order to obtain a clean
and straight cut.
•
Check the bottom of the robot lawn mower for
dirt at regular intervals. Clean the robot lawn
mower regularly. Remove heavy soiling imme-
diately.
•
Heavy soiling of the robot lawn mower is pos-
sible in the first weeks of its use if you previ-
ously worked with a conventional lawn mower.
In these first few weeks you should check the
bottom of your robot lawn mower more often.
•
Shorten the lawn only in small steps in order
to prevent heavy soiling.
•
There are no other parts inside the tool which
require maintenance.
7.2.1 Replacing the blades
Use only original blades or correct performance
and safety cannot be guaranteed.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the ef-
fi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 10 - Caution! - Wear work gloves:
- 54 -