Wilo Stratos MAXO Notice De Montage Et De Mise En Service page 4

en-US
Table of Contents
1 General ................................................................ 6
1.1 About this manual ..................................... 6
1.2 Copyright .................................................... 6
1.3 Subject to changes.................................... 6
1.4 Exclusion from warranty and liability...... 6
2 Safety .................................................................. 6
2.1 Identification of safety instructions ....... 7
2.2 Personnel qualifications ........................... 8
2.3 Electrical work............................................ 9
2.4 Operator's obligations ............................ 10
3 Description of pump ....................................... 11
3.1 Permissible installation positions.......... 13
3.2 Type key.................................................... 13
3.3 Technical data .......................................... 14
3.4 Bluetooth interface ................................. 15
3.5 Minimum inlet pressure .......................... 15
3.6 Scope of delivery ..................................... 16
3.7 Accessories ............................................... 16
4 Intended use and misuse................................ 17
4.1 Intended use............................................. 17
4.2 Improper use............................................. 19
4.3 Safety instructions .................................. 19
5 Transport and storage .................................... 20
5.1 Transport inspection ............................... 20
5.2 Transport and storage conditions ......... 20
5.3 Transport .................................................. 21
6 Installation....................................................... 21
6.1 Operator's obligations ............................ 21
6.2 Safety ........................................................ 22
6.3 Preparing installation .............................. 22
6.4 Installation ................................................ 23
6.5 Aligning the motor head......................... 25
6.6 Insulating .................................................. 28
6.7 After installation ...................................... 29
7 Electrical connection ...................................... 29
7.1 Requirements ........................................... 30
7.2 Connecting the temperature sensor cable
.................................................................... 33
7.3 Connection options................................. 33
7.4 Connecting and dismantling the Wilo-
Connector ................................................. 34
4 Installation and operating instructions • Wilo-Stratos MAXO/-D/-Z • Ed.02/2023-10
7.5 Connecting communication interfaces
................................................................... 38
7.6 Analog input (AI1) or (AI2) – purple ter-
minal block............................................... 41
7.7 Digital input (DI1) or (DI2) – grey terminal
block ......................................................... 43
7.8 Bus Wilo Net (green terminal block)..... 44
7.9 Collective fault signal (SSM) – red termi-
nal block ................................................... 45
7.10 Collective run signal (SBM) – orange ter-
minal block............................................... 45
7.11 CIF module ............................................... 45
8 Commissioning ................................................ 46
8.1 Filling and venting................................... 46
8.2 Flush.......................................................... 47
8.3 Procedure after switching on the power
supply during initial commissioning..... 47
8.4 Description of operating elements....... 48
8.5 Operating the pump ............................... 49
9 Setting the control functions ........................ 60
9.1 Basic control functions........................... 60
9.2 Additional control functions ................. 63
9.3 Settings assistant.................................... 66
9.4 Predefined applications in settings assis-
tant............................................................ 79
9.5 Settings menu - Set control mode....... 84
9.6 Adjustment - Manual operation ........... 88
9.7 Configuration storage/data storage..... 90
10 Twin-head pump operation ........................... 90
10.1 Function ................................................... 90
10.2 Settings menu ......................................... 93
10.3 Display for twin-head pump operation
................................................................... 95
11 Communication interfaces: Setting and func-
tion.................................................................... 97
11.1 Application and function of SSM relay
................................................................... 97
11.2 Application and function of SBM relay
................................................................... 98
11.3 SSM/SBM relay forced control............. 100
11.4 Application and function of the digital
control inputs DI1 and DI2................... 100
11.5 Application and function of the analog
inputs AI1 and AI2................................. 104