Setting Max. Speed On / Off Function; Switch Over Setpoint 1/2 And Pband 1/ 2 For Control Circuit 1 - Helios FU Comfort Sinus Manuel De Montage Et D'utilisation

Installation and Operating Specification FU Comfort Sinus
9.9.6.10

Setting Max. Speed ON / OFF function

The value for "Max Speed" adjusted in menu "Settings", is activated over a digital input. I.e. the unit
works independently of the controller function firm with this value.
Contact e.g. at ditgital input "Digital In 1" (depending on device type at terminals "D1" - "D1"or "D1" -
"24 V").
This function influences both circuits in operation with two control circuits.
Controller
Display depending on device type in: %, Hz, rpm
1 Setting "Max. Speed" or "1.Max. Speed" and "2.Max. Speed" for
operation with two control circuits
9.9.6.11

Switch over Setpoint 1/2 and Pband 1/ 2 for control circuit 1

Switching between "1st setpoint 1" / "1st setpoint 2" and "1st Pband 1" / "1st Pband 2" (from
2.03
for ).
Function basically the same as
When programming this function, "Setting" additionally lists the parameter: "1.Pband 1. for control
circuit 1"
Contact e.g. at ditgital input "Digital In 1" (depending on device type at terminals "D1" - "D1"or "D1" -
"24 V").
Example for "D1 Inverting" = "OFF":
•
With open contact: "1.Setpoint 1" = 20 °C + "1.Pband 1" = 5 K
•
With closed contact: "1.Setpoint 2" = 17 °C + "1.Pband 2" = 3 K
1.Setpoint1 Setting "1.Setpoint 1" = Setpoint 1 of control circuit 1
1.Pband1 Setting "1.Pband 1" = Pband 1 von control circuit 1
1.Setpoint2 Setting "1.Setpoint 2" = Setpoint 2 of control circuit 1
1.Pband2 Setting "1.Pband 2" = Pband 1 von control circuit 1
Info
28.7 °C
E1 Actual
L-BAL-E304-GB 2004
1
- - - - -
= 80 %
1
= 0 .. 100 %
0
24V
D1 D1
0 1
| |
5D , it is additionally switched over to Pband 2.
15D
Operation with "1.Setpoint2" and "1.Pband2" is signalized by the moon symbol for
reduced operation.
If Setpoint 2 was activated additionally for control circuit 1 or control circuit 2 by a digital
input with function
If Setpoint 2 and Pband 2 were activated additionally for control circuit 2 by a digital
input with function
| |
11D
•
"D1 Inverting"
active at closed contact
• "D1 Inverting"
active at opened contact
15.05.2009
v_11d_max_drehzahl.vsd
Controller 1
A1
Controller 2
A2
D1
24V
D1
v_15d_umsch_sollw_plus_regelb_kreis1.vsd
Sensor 1 Sensor 2
| | | |
5D / 9D the moon symbol is already switched on.
| |
16D , the moon symbol is already switched on.
Part.-No.
81/139
Programming
"OFF" "Max. Speed"
= :
"ON" "Max. Speed"
= :
| |
15D
n = 0 - 100 %
n = 0 - 100 %
04.04.2013
2.01
, not