Settings For Operation Modes 2.01 - Helios FU Comfort Sinus Manuel De Montage Et D'utilisation

Installation and Operating Specification FU Comfort Sinus
Base setup
OFF
E2 Function
9.2.2 Settings for operation modes
2.01
Temperature control airconditioning and refrigeration
(preset Setpoint 20.0 °C, P-band 5.0 K)
2.03
Temperature control with pre-programmed additional functions (heating, shutter, temperature monitor-
ing).
2.04 Temperature control with 2 sensors
Comparison with control to higher value "E2 Function" set to comparison
operation: "Control value "
Alternative: Average calculation of 2 measuring places "E2 Function" set to
operation: "Average E1 / E2 "
2.05 Temperature control with 2 sensors, regulation on difference temperature.
Display during operation: "Value of E1 - E2" in K, "E1" = reference temperatur, "E2" causes positiv (E2
< E1) or negative (E2 >E 1) difference.
Main menu
Setting
Protocol
Base setup
Controller Setup
IO Setup
Setting
20.0 °C
Setpoint1
Setting
- - - - -
Set Internal2
L-BAL-E304-GB 2004
E2 Function
The second signal input is not activated at the factory for modes with one sensor.
In modes with two sensors, the function is automatically programmed. The second
analog input is thus assigned and no other function assignments are possible.
|
•
2.04 4E
E2 Function at
higher temperature. Alternative: average of 2 measuring points for this must be
reprogrammed on function
|
•
2.05
5E
E2 Function at
between sensor 1 and sensor 2. Preprogrammed sensor type
"E2 Function"
Adjustable
• | |
1E
= External Setpoint e.g. via external signal (0 - 10 V) instead of
"E1 Analog In"
– For sensor type
– For sensors with active signal: 0 - 10 V
• | |
2E
=External manual operation via external signal (0 - 10 V). Switch over between
settings on the device and external manual operation via digital input (see IO Setup:
| |
7D
function ).
• | |
6E
= sensor for outdoor temperature-dependent setpoint adaptation (at
possible), pre-programmed sensor type
– additional parameters menu group
– additional parameters menu group
– Example see setting for operation
• | |
7E
= Measurement value = Measurement value e.g. for limit indication, display in
"E2 Actual"
Info menu .
• | | | |
8E 13E
... = sensor input for control circuit 2 (at
setup / operation with second control circuit.
2.01 ... 2.05
Setting
Setpoint1
Setting range with passive sensor type "TF", "PT1000": -50.0...150.0 °C
Factory setting: 2.01 , 2.03
2.05 : 0.0 °C
at
Set Internal2
Setting "Setpoint 2" e.g. reduced value for night operation.
Switch over Setpoint 1/2 over external contact (display as long as noch allocation is
| |
carried out: - - - - - IO Setup).
Part.-No.
36/139
|
preprogrammed = comparison value with control to
| |
3E
preprogrammed sensor type
|
preprogrammed = regulation on difference temperature
"TF or PT1000"
=
0 - 100 % sensor measuring range.
"TF.."
.
"Setting"
: T-Band, T-Start SA, Min. Setpoint.
"Info"
: Setpoint Control
4.01 4.02
+ additional menu items.
2.03
, 2.04 : 20.0 °C
Programming
"TF"
.
"TF"
.
"Setpoint 1"
: 0 - 10 V -50.0...+150 °C.
2.03
not
not possible) see Base
| |
4E . Display during
| |
3E . Display during