Intern / Extern Function | 6D; Automatic Control / Speed Manual Function | 7D - Helios FU Comfort Sinus Manuel De Montage Et D'utilisation

Installation and Operating Specification FU Comfort Sinus
2
- - - - -
1
- - - - -
1 Setting "Setpoint 1" or "1.Setpoint 1" (display in operation with two
control circuits for Setpoint 1 of control circuit 1)
2 Setting "Setpoint 2" or "1.Setpoint 2" (display in operation with two
control circuits for Setpoint 2 of control circuit 1)
Info
28.7 °C
E1 Actual
9.9.6.6 Intern / Extern Function
For Mode Speed controller
"Set extern1" under settings must be programmed to "OFF".
Contact e.g. at ditgital input "Digital In 1" (depending on device type at terminals "D1" - "D1"or "D1" -
"24 V").
Si 40 %
1
- - - - -
Si Signal
1 Setting "Set Intern1" (depending on device type in: %, Hz, rpm)
For operation as controller (starting from
Possible only for operation with one control circuit!
Under Base setup "E2 function" programmed to function
Contact at digital input e.g. "Digital In 1" = "D1" - "D1"
1
1 Setting "Setpoint1"
ES External Setpoint e.g. 5 V
Se Sensor
9.9.6.7 Automatic control / speed manual Function
Possible only for operation with one control circuit!
Switch over between automatic control to set target value (depending on the activation: "Setpoint1",
"Setpoint2") and the default for "manual operation" set at the device.
L-BAL-E304-GB 2004
Controller
n = 0 – 100 %
24V
D1 D1
0 1
Operation with "Setpoint2" is signalized by the moon symbol for reduced operation.
| |
6D
1.01 : Switch over "Set Intern" / "Set external "
E1
Controller
n = 40 %
1
0
n = 80 %
24V
D1 D1
0 1
- - - - -
Controller
n = 0 – 100 %
ES E2
24V
D1 D1
0 1
23.8°C
• "D1 Inverting"
18 °C at opened contact /
25 °C at closed contact.
• "D1 Inverting"
at closed contact /
opened contact.
Sensor
11.05.2007
v_5d_sollwert_1_2.vsd
•
"D1 Inverting"
opened contact /
contact.
• "D1 Inverting"
closed contact /
contact.
11.05.2007
v_6d_vorgabe_intern_extern.vsd
2.01 ): switch over "Setpoint 1" / "external Setpoint "
| |
for "external setpoint" .
1E
• "D1 Inverting"
opened contact / Signal Extern at closed
contact
• "D1 Inverting"
at closed contact / Signal Extern at opened
Se
contact
26.05.2010
v_6d_sollwert1_externer_sollwert.vsd
| |
7D (mode 2.01
Part.-No.
79/139
Programming
"OFF" "Setpoint1"
= :
"Setpoint2"
"ON" "Setpoint1"
= :
"Setpoint2"
"OFF" "Set Intern1"
= :
"Setting Extern"
"ON" "Set Intern1"
= :
"Set Extern"
at opened
"ON"
= : Setting at the unit at
"OFF"
= : Setting at the unit
)
=
=
= 18 °C
= 25 °C at
at
at closed
at