Samsung SINAMICS G130 Mode D'emploi page 1165

M_suppl 1
p1511[C]
(0)
M_suppl 1 scal
M_supply 2 scal
p1512[C]
-2000.0 %...2000.0 %
(0)
p1514[D] (100.0 %)
M_suppl 2
p1513[C]
(0)
Calculated accelerating torque
[6031.8]
M_max upper effective
[6640.8] r1538
M_max upper scal
p1540[C]
(1)
M_max up. w/o offs
[6630.8] r1526
M_max up w/o offs
p1552[C]
(1)
0 = Speed control
1 = Torque control
p1501
r1406.12
[2520.3]
1
p1300 = M
Ctr
M_set from speet controller
[6040.8]
M_max u Skal oOffs
p1554[C]
(1)
M_max low w/o offs
[6630.8] r1527
M_max nctr lowScal
p1541[C]
(1)
M_set
[6640.8] r1539
<1> The signal is only effective after magnetization has been completed (r0056.4 = 1).
<2> Acceleration control is inhibited for p1517 = 100 ms.
1 2
DO: VECTOR, VECTORGL, VECTORMV, VECTORSL
Vector control - Torque setpoint
+
p1400.14 1 = Torque pre-control
+
[6490.7]
p0856 1 = Speed controller enable
r0898.12
[2501.7]
Vdc_max controller active
r0056.14 <5>
[2526.6]
1
0
0
0
0
1
Min
Example:
0 = Fast stop
active (OFF3)
M_max lower eff
r0899.5
r1539
M_lim var/fixed S_src
Torque control active
r1407.2
[6030.5]
n_ctrl PI-M_output
0
M_soll
p1503[C]
1
M_setp sv SLVC
(0)
[6726.8]
r1538
Max
<3> M_set is also influenced by the speed limit controller.
<4> Only for DO: VECTOR and sensorless FEM with speed controller inhibited r1776[4] = 0.
3 4
0
0
1
1
0...100.00 [ms]
<1> <1>
<2>
p1517[D] (4.00)
M_accel unsmooth M_accel smooth
r1518[0] r1518[1]
0
M_max output n_ctrl upper limit
r1547[0]
1
1
Torque limiting, upper active
p1551[C]
(1)
M_set before M_suppl
Min
r1508
r1480 [6030.1] [6722.1]
[6726.7]
r1617
Torque limiting lower active
Max
<5>
1
M_max output n_ctrl lower limit
r1547[1]
0
5
fp_6060_51_eng.vsd
31.03.10 V04.05.00
p0115[1] (Motor Modules)
Refer to [1020.7]
M_suppl total
r1515
+
M_suppl+M_accel
+
r1516
Torque limiting
without Pre-control
r1407.15
r1407.8
[2522.3]
Torque limiting upper active
+
<3>
+
Torque limiting
Torque limiting lower active
r1407.9 [2522.3]
Current/torque limit active
Torque limit reached
1
<5> Not for DO. VECTORGL.
6 7
Function diagram
SINAMICS
<1>
r1407.8
[2522.3]
M_set total
r0079
[6030.1] [6710.1]
[8012.1]
r1407.9
[2522.3]
r0056.13
[2526.2]
r1407.7
[2522.3]
8
- 6060 -