Samsung SINAMICS G130 Mode D'emploi page 1155

Ramp-up time
0.000...999 999.000 [s]
p1120[D] (10.000)
Up ramp scaling
p1138[C]
(1)
p1122 1 = Bypass ramp-function generator
[2505.3] r1198.15
p1142
1 = Enable speed setpoint
[2501.3] r0898.6
RFG setpoint at the input
1
r1119
[3050.8]
0
0
p1141 0 = Freeze ramp generator
<5>
[2501.3] r0898.5
1 = Internal RFG enable
[2634.4]
0 = Internal fast stop
[2634.4]
Set ramp-function generator
p1143[C]
(0)
Ramp-function generator setting value
p1144[C]
<1> Not at S150/G130/G150.
<2> Effective ramp-up time: Tup_eff = Tup + (IR/2 + FR/2)
Effective ramp-down time: Tdn_eff = Tdn + (IR/2 + FR/2)
<3> p1151.00 = 0: Rounding-off at zero crossover enabled.
p1151.00 = 1: Rounding-off at zero crossover disabled.
<4> p1134 = 0: Rounding-off is always active.
Overshoots can occur.
p1134 = 1: Final rounding-off is not effective
when the setpoint is suddenly
reduced during ramp-up.
<5> For SERVO and VECTOR, the following applies: Inhibited during jogging.
<6> After a 0/1 signal a ramp-up is started again.
<7> With simultaneous jog 1 and 2 (p1055 = p1056 = 1) the last setpoint remains effective (Freeze ramp-function generator).
<100> For SERVO, the following applies: Only if the function module "extended setpoint channel" is activated (r0108.8 = 1).
<101> To view the pre-assignment of the sampling times in p0115, refer to p0112.
1 2
DO: SERVO, VECTOR, VECTORGL, VECTORMV, VECTORSL
Setpoint channel - Extended ramp-function generator
Ramp-down time
0.000...999 999.000 [s]
p1121[D] (10.000)
Down ramp scaling
p1139[C]
(1)
0 = Internal fast stop
[2634.4]
0
Ramp flattening-off
[3080.8]
Freeze ramp-function generator
y
0
1
x
p1082
1
0
0
1
<4>
<7>
-p1082
RFG rounding-off type
dy/dt IR
0...1
p1134[D] (0)
(0)
Tup_eff <2>
t
t
n
t
set
3 4
OFF3 OFF3
Ramp-down time Initial rounding-off Initial rounding-off
0.000...600.000 [s] 0.000...30.000 [s] 0.000...30.000 [s]
p1135[D] (0.000) p1136[D] (0.000)
p1130[D] (0.000)
0
0 1
0
0
1 0 1
IR
Extended ramp-function
Tup Tdn
x
generator
y
<3>
FR IR FR IR FR
Tdn_eff <2>
x
+ –
y
p1082
n_max
[3050.5]
[3095.7]
<1>
5
fp_3070_51_eng.vsd
24.10.11 V04.05.00
OFF3
Final rounding-off Final rounding-off
0.000...30.000 [s] 0.000...30.000 [s]
p1137[D] (0.000)
p1131[D] (0.000)
1 0 1
FR
0
y
1 = Ramp-function
p1140 generator enabled
[2501.3] r0898.4
IR FR
HLG acceleration
r1149
t
Other status bits
1
Ramp-up active
Ramp-down active
0
Threshold for
"Ramp-up/ramp-down active"
0.00...1000.00 [rpm]
p1148[D] (19.80)
6 7
Function diagram
SINAMICS
p0115[3]
Refer to
[1020.7]
<101>
0
n_set_5
[3080.1]
1
<6>
Ramp-function
generator,
status bits
[3080.5]
8
- 3070 -