ev3 ARTISSE ISD-5 Mode D'emploi page 7

Suggested distances between mobile RF-Communication Devices
and Artisse™ Detachment Device
The Artisse™ Detachment Device is intended for use in the
electromagnetic environment in which radiated
Disturbances are controlled . The customer or user of the
device can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile
RF Communications Equipment and the device as recommended
below, according to the maximum output power of the
communications equipment .
Distance depending on the Sending Frequency:
Rated Separation distance according to frequency
maximum
output
150kHz to
power of
80MHz
transmitter
d=1.17
W
0.01 0.12
0.1 0.37
1 1.17
10 3.69
100 11.67
For transmitters rated at a maximum output power not listed
above, the recommended separation distance d in meters (m) can
be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
NOTE1: At 80 MHz and 800 MHz, the separation distance for the
higher frequency range applies.
NOTE2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Electromagnetic Immunity
The Artisse™ Detachment Device is intended to be used in the
electromagnetic Environment specified below. The customer
or user of the device should ensure that it is used in such an
environment .
IEC 60601 Test
Immunity Test
Conducted RF
IEC 61000-4-6 150kHZ to 80 MHz
Radiated RF
IEC 61000-4-3 80MHz to 2 .7 GHz
of transmitter
80MHz to 800MHz to
800Mhz 2.5 GHz
P P
d=1 d= 2.33
0.12
0.37
1.17
3.69
11.67 23.33
Compliance Level
level
3 Vrms 3 Vrms (V1)
3 V/M 3V/m (E1)
Portable and mobile RF communications equipment should be
used no closer to any part of the Artisse™ Detachment Device,
including cables, than the recommended separation distance
calculated from the equation applicable to the frequency of the
transmitter .
P
d= 1 .17
P
d= 1 .17
P
d= 2 .33
Where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and d is
the recommended separation distance in meters (m) .
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey
level in each frequency range
Interference may occur in the vicinity of equipment marked with
P
the following symbol:
0.23
0.74
2.33
7.38
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range
applies .
NOTE 2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a . Field strengths from fixed transmitters, such as base stations
for radio (cellular/cordless) telephones and land mobile radios,
amateur radio, AM and FM radio broadcast and TV broadcast
cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fixed RF transmitters,
an electromagnetic site survey should be considered. If the
measured field strength in the location in which the Artisse™
Detachment Device is used exceeds the applicable RF
compliance level above, the Artisse™ Detachment Device
should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be
necessary, such as reorienting or relocating the Artisse™
Detachment Device .
b . Over the frequency range 150 kHz to 80 MHz, field strengths
should be less than [V1] V/m .
5
Electromagnetic Environment Guidance
for 80 MHz to 800 MHz
for 800 MHz to 2 .5 GHz
should be less than the compliance
a
.
b