Publicité
Les langues disponibles
Les langues disponibles
R R e e c c o o m m m m e e n n d d e e d d s s e e p p a a r r a a t t i i o o n n s s d d i i s s t t a a n n c c e e s s b b e e t t w w e e e e n n p p o o r r t t a a b b l l e e a a n n d d m m o o b b i i l l e e R R F F c c o o m m m m u u n n i i c c a a t t i i o o n n s s e e q q u u i i p p m m e e n n t t a a n n d d P P o o w w e e r r - -
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz,
the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.
P P o o w w e e r r - - P P R R O O is suitable for use in the electromagnetic environment specified below. The customer or the user of P P o o w w e e r r - -
P P R R O O should assure that it is used in such an environment.
I I m m m m u u n n i i t t y y t t e e s s t t
Electrostatic discharge
(ESD)
IEC 61000-4-2
Electrostatic fast Transient/
burst
IEC 61000-4-4
Surge
IEC 61000-4-5
6516-209-005 Rev AA.0
1 1 5 5 0 0 k k H H z z t t o o 8 8 0 0 M M H H z z
D D = = ( ( 1 1 . . 2 2 ) ) ( ( √ √ P P ) )
0.12
0.38
1.2
3.8
12
G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y
I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l
+6 kV contact
+8 kV air
+2 kV for power supply lines
+1 kV for input/output lines
+8 kV line(s) to line(s)
+2 kV line(s) to earth
P P R R O O
8 8 0 0 M M H H z z t t o o 8 8 0 0 0 0 M M H H z z
D D = = ( ( 0 0 . . 1 1 8 8 ) ) ( ( √ √ P P ) )
0.018
0.57
0.18
0.57
1.8
C C o o m m p p l l i i a a n n c c e e l l e e v v e e l l
+6 kV contact
+8 kV air
+2 kV for power supply lines
+1 kV for input/output lines
+8 kV line(s) to line(s)
+2 kV line(s) to earth
8 8 0 0 0 0 M M H H z z t t o o 2 2 . . 5 5 G G H H z z
D D = = ( ( 0 0 . . 3 3 5 5 ) ) ( ( √ √ P P ) )
0.035
0.11
0.35
1.1
3.5
E E l l e e c c t t r r o o m m a a g g n n e e t t i i c c
e e n n v v i i r r o o n n m m e e n n t t - - g g u u i i d d a a n n c c e e
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%. Applies to:
•
P P o o w w e e r r - - P P R R O O
•
S S M M R R T T charger (6500-
201-010)
Mains power quality should
be that of a typical
commercial or hospital
environment. Applies to:
•
S S M M R R T T charger (6500-
201-010)
Mains power quality should
be that of a typical
commercial or hospital
environment. Applies to:
•
S S M M R R T T charger (6500-
201-010)
53
EN
Publicité
