Stryker Power-PRO IT Cot Mode D'emploi page 8

• Always follow proper hand placement on hand grips. Keep all hands clear of the red safety bar pivots when you load,
unload, or change the cot height position.
• Do not ride on the base of the cot.
• Do not transport the cot sideways to avoid the risk of tipping. Always transport the cot in a lowered position, head end or
foot end first to minimize the risk of tipping.
• Always keep hands, fingers, and feet away from moving parts. Use caution when placing your hands and feet near the
base tubes while you raise or lower the cot.
• Always conduct patient monitoring when the cot is idle. If you hydraulically raise or lower the product you may
temporarily affect electronic patient monitoring equipment.
• Do not leave a patient unattended. Hold the product while a patient is on the product.
• Do not apply a wheel lock when a patient is on the product or when you move the product to avoid the risk of tipping.
• Always transport the cot at a lower height to reduce the risk of a cot tip. If possible, obtain additional assistance or take
an alternate route.
• Always avoid high obstacles, such as curbing, steps, or rough terrain to avoid the risk of the product tipping over.
• Do not use the jog function to jog past the set cot load height after the cot safety bar connects with the vehicle safety
hook.
• Always use two operators to raise or lower the cot with a patient.
• Always use P P o o w w e e r r - - L L O O A A D D with the 6085/6086 P P e e r r f f o o r r m m a a n n c c e e - - P P R R O O XT, 6500/6506 P P o o w w e e r r - - P P R R O O XT, and 6510/6516
P P o o w w e e r r - - P P R R O O IT cots with the P P o o w w e e r r - - L L O O A A D D option only. In certain situations, you can use P P o o w w e e r r - - L L O O A A D D as a standard
antler for most X-frame cots, but a rail clamp assembly is required for all cots without the P P o o w w e e r r - - L L O O A A D D option.
• Always make sure that you use a P P o o w w e e r r - - P P R R O O date of manufacture cot with the Stryker Model 6390 P P o o w w e e r r - - L L O O A A D D
system to avoid the risk of injury.
• Always support the load of the patient, cot, and accessories after the weight is off of the ground.
• Always use two operators when a cot is occupied.
• Do not load the cot into a vehicle with the head section retracted when using a cot fastener. The cot may tip or not
connect with the cot fastener.
• Always use the powered method to load an unoccupied cot with one operator. Do not use the manual method to load an
unoccupied cot with one operator.
• Always make sure that two operators are present when a cot is occupied.
• Do not pull or lift on the cot safety bar when you unload the cot.
• Always set the cot transfer wheels safely on the ground when you unload the cot from the vehicle patient compartment
to avoid the risk of product damage.
• Do not press the extend (+) button until the safety bar connects with the vehicle safety hook.
• Always lock the head section into place before you operate the cot.
• Do not install or apply a wheel lock on a product with worn wheels that are less than 6 in. diameter.
• Do not leave a patient or occupant unattended. Hold the product while a patient or occupant is on the product.
• Do not install these incubator adaptors on any other Stryker cot or on any cot from another manufacturer. These
incubator adaptors are for use only on the P P o o w w e e r r - - P P R R O O IT cot.
• Always make sure that the incubator adaptor is properly installed on the cot and the incubator is securely fastened to the
incubator adaptor before use.
• Stryker is not responsible for specification changes to the D D r r a a g g e e r r ® (or A A i i r r - - S S h h i i e e l l d d s s ® Series) incubators.
• Do not install the sled receptacle on any other Stryker cot or on any cot from another manufacturer. These sled
receptacles are for use only on the P P o o w w e e r r - - P P R R O O IT cot.
• Stryker is not responsible for specification or option changes to airsled compatible incubators.
• Do not allow the head end storage flat (if equipped) to interfere with the operation of the retractable head section, safety
bar, or vehicle safety hook.
• Do not attempt to open the battery pack for any reason, to avoid the risk of electric shock. If the battery pack case is
cracked or damaged, do not insert it into the charger. Return damaged battery packs to a service center for recycling.
• Always avoid direct contact with a wet battery or battery enclosures. Contact may cause injury to the patient or operator.
• Do not insert a cracked or damaged S S M M R R T T Pak into the S S M M R R T T charger. Return damaged S S M M R R T T Paks to a service
center for recycling.
• Always have a certified mechanic, familiar with ambulance vehicle construction, install the mounting bracket option and
the S S M M R R T T charger.
EN 4 6516-209-005 Rev AA.0