Battery Charger - Champion Global Power Equipment 100199 Mode D'emploi

Model 100199
INSTALLATION
16. Pin 16 Gen AC Detect
DIP SWITCHES on the backside of the control, between the 2
rows of pin connectors
The Dip Switches set parameters of the controller for delay
sequences. There are only 10 dip switches. These are the
designated "ON" or "OFF" position settings for the dip switches;
1. Position 1 is in the "ON" position
2. Position 2 is in the "ON" position
3. Positions 3 – 9 are in the "OFF" position
4. Position 10 is in the "ON" position
These are factory set delays or activation signals.

BATTERY CHARGER

This automatic battery charger is an intelligent module which
maintains lead acid batteries at a full charge, when the HSB has
been properly installed. Continual monitoring and maintenance
will promote long battery life. In accordance with the principle of
high efficiency, at Full Load, >85% of efficiency is achieved. This
charger is a maintenance battery charger. If the battery voltage
falls below 6V, the charger will not re-change the batteries.
To properly maintain battery efficiency you must follow the
battery manufacturers; safety instructions, warnings and proper
maintenance procedures.
Feature benefits include; reverse polarity protection, short
circuit protection, overload protection, over voltage, over current,
floating charging system, constant voltage output and a rugged
design for industrial environments. The charger is also equipped
with a manual reset which is located on the far right side of the
wire land points. This charger is for lead acid batteries only. All
adjustments are preset at the factory.
The automatic battery charger has five (5) built in LEDs that
display the following, view left to right;
40
Part No. 101049 Rev. B
R (Red)
ALIMENTATION
RECOGNIZED
COMPONENT
AUTOMATIC BATTERY CHARGER /
CHARGE AUTOMATIQUE DE BATTERIE /
CARGADOR DE BATERÍA AUTOMÁTICO
Conforms to UL
MODEL / MODÈLE / MODELO : 100482
Std. 1236
Power: 80-125 Vac 1.0 A 50 / 60 Hz
Alimentation : 80-125 V c.a. 1,0 A 50 / 60 Hz
Potencia: 80 - 125 V C.A. 1,0 A 50 / 60 Hz
POWER / ALIMENTATION /
POTENCIA
L N
1. Power – Lit to indicate the battery is fully charged.
Black
PMS 109 C
2. Small Bar – Lit to indicate the battery is receiving a trickle
PMS 485 C
PMS Reflex Blue C charge.
3. Middle Bar – Lit to indicate current output is near 50%.
4. Large Bar – Lit to indicate the charger is operating above
50% capacity.
5. NO CHARGE – Lit to indicate a battery charging problem.
If this LED is lit, the LED on the Engine Controller module,
"LOW BATTERY" will also be lit.
The battery(s) might be discharged to a level that is too low to re-
charged with this charger (battery voltage below 6V). If this is the
case, the batteries will need to be charged individually. Remove
all battery cables from the batteries and follow the battery
manufacturers' instructions on properly servicing/charging the
batteries.
Be careful to avoid corrosion on the battery post(s). Corrosion
can have the effect of creating an insulation between the post(s)
and the cable(s), this will severely affect the performance of the
battery. Follow battery manufacturers' instructions on proper
maintenance, service or replacement. The correct wire lands are
read left to right, 6 land points;
NO CHARGE / PAS DE CHARGE /
SIN CARGA
POWER
POTENCIA
E. O.
Output: 24 Vdc 1.6 A
Sortie : 24 V c.c. 1,6 A
Producción: 24 V C.C. 1,6 A
OUTPUT / SORTIE /
V
PRODUCCIÓN
ADJ