Defining / Adjusting The Free Mixers Menu: ( Mixer ) Mixdef; Adjusting The Mixer Effect - Multiplex COCKPIX SX Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Example: offset four-point swashplate
1
4
2
3
90° arrangement:
You can set the C
OCKPIT
on the right if you are using swashplate type 4 and set
V-DREH to 45.
17. The free mixers MIX 1, 2 and 3
The C
SX features three free mixers. The mixers
OCKPIT
are of equal value, and are set up and adjusted in the
same manner. All three mixers can also be used simul-
taneously.
In the EASY model type only MIX 1 is available. In the
model types GLIDER, ACRO and HELI you can work
with all three mixers if you wish.
How do the free mixers work?
A free mixer allows you to mix the control signal of one
transmitter control (source) into the control signal for a
servo (destination). The two control signals are simply
summed (added together). A switch can also be as-
signed to the mixer, so that the mixer input can be
switched on or off.
Two steps are required to prepare a free mixer:
a.
Defining the mixer (17.1.)
Define the destination and the switch
b.
Setting the mixer effect (
Define the magnitude of the mixer input
17.1. Defining / adjusting the free mixers
) MIXDEF
Menu: (
MIXER
The MIXDEF menu is used to define the source, desti-
nation and switch for the free mixers.
Moving to the MIXDEF menu:
to MENU,
(SETUP appears),
to MIXER,
(TH >S4 appears),
to MIX1
(MIXDEF appears)
If the MIXDEF menu does not appear, the mixer is
already defined, and can now be adjusted (
Rotated
through 45°
SX to the arrangement shown
17.2)
17.1.).
Operating Instructions
Press the 3-D digi-adjustor again briefly to open the
menu for defining the mixer.
In the right-hand picture AILERON is selected as the
source. The destination is servo 5. The mixer input is
switched on when switch 1 (CS/A-ROT) is in the for-
ward position.
a.
Select the source
Move the stick / slider briefly
(Quick-Select)
The trims are not taken into account
b.
Select the destination
Servo 1 to 7; use the 3-D digi-adjustor
c.
Select the switch
Move the desired switch (Quick-Select);
The code number (1 to 4) appears
Move the switch to the
"mixer input active" position; the
hyphen indicates the selected setting
Code
Switch name
No.
CS
1
A-ROT
2
D-R
SNAP
3
DTC
PH
4
AUX 2
You can change the source, destination and switch in
any way, as long as you remain in this menu.
Once you have selected the source, destination and
switch, press the 3-D digi-adjustor
the MIXDEF menu.
Note: removing the switch
If you have assigned a switch when defining the mixer,
the switch can be changed, but not removed.
If you wish the mixer to work constantly, you must not
assign a switch to it. The only means of removing the
switch is to erase the definition (
define the mixer without a switch.

17.2. Adjusting the mixer effect

If you wish to continue, and adjust the effect of the
mixer, turn the 3-D digi-adjustor one click to the left
the menu shown below then appears.
Page 73
Source Switch Target
Function
Combi-Switch
Auto-rotation
Dual Rate
Snap Flap
Direct Throttle
Flight phases
Aux. channel AUX2
briefly to return to
11.4.), and then re-
;

Publicité

Table des Matières
loading

Table des Matières