Preparing The Transmitter; Setting Up A New Model Memory For Easy Menu: ( Memo ) New; Setting The Stick Mode (Which Stick Controls Which Function?) Menu: ( Setup ) Mode - Multiplex COCKPIX SX Manuel D'utilisation

C SX
OCKPIT
1
Delta
left
4
Throttle
Fig. 12.3. Servo assignment, delta

13.3. Preparing the transmitter

The following steps are necessary when preparing the
transmitter for a particular model:
• Set up the model memory
• Set the correct stick mode
• Learn the layout of the controls
(switches / sliders)
• Determine the idle setting for throttle and spoilers
• Set up throttle check
13.3.1. Setting up a new model memory for EASY
) NEW
MEMO
Menu: (
Moving to the NEW menu:
Action
Left to MENU
1.
Confirm
Right to MEMO
2.
Confirm
Right to NEW
3.
Confirm
The screen
displays the
model type you set
up.
(e.g. EASY)
Turn the 3-D digi-adjustor to select the model type:
EASY is the default. Confirm the model type with a
brief press ; this takes you automatically to the
IN MEM menu. Here you can select the memory for
the new model. The memory number is displayed flash-
ing in the bottom line of the screen.
Use the 3-D digi-adjustor to select the memory in which
you wish to store the new model. Memories which al-
ready contain model data are not offered when you leaf
through; this means that you cannot accidentally over-
write an existing model.
SPOILER/
6
THR-LIMIT
PH
7
AUX 2
3
2
Rudder
Delta
5 Elevator
right
13.3.1.
13.3.2.
13.3.3.
12.3.4.
13.3.5.
Effect
SETUP appears
GO TO appears
now
last
Confirm the selected memory with a brief press
the 3-D digi-adjustor. This takes you to the menu where
you can enter the model name.
Note: interrupting (without a new model)
If you end up at this menu point accidentally, or if you
have selected the wrong model type, you can interrupt
the process simply by selecting "0" as the memory.
Alternatively a long press
takes you back to the INFO 1 display.
A further brief press
activates input mode: the first character flashes.
The default name is <EASY>, but it can be changed to
any name you like.
Changing the model name
Use the 3-D digi-adjustor to search for the desired
character. The following characters are available:
0 to 9, :, /, <, -, >, ?, space, A to Z
Press the 3-D digi-adjustor again briefly .
The second character now flashes, and can be se-
lected in the same way.
Continue until you have entered all six characters.
When the name is complete, close the name input
process with a brief press of the 3-D digi-adjustor.
Note: interrupting the name input process
If the name is complete before the sixth character, you
can interrupt the process with a long press on the 3-D
digi-adjustor . This takes you back to the INFO 1
display.
The model is now stored in the memory, and you are
returned to the "NAME" menu. You can move to the
other menus via "EXIT", or go directly to the INFO 1
display with a long press
13.3.2. Setting the stick mode
(which stick controls which function?)
Menu: (
The stick mode determines which transmitter controls
operate the functions aileron, elevator, rudder, throttle
and spoiler. Eight modes are available.
In modes 1 to 4 THROTTLE is assigned to a stick, and
SPOILER is on the right-hand slider. In modes 5 to 8
the assignment for aileron / elevator / rudder is the
same, but SPOILER and THROTTLE are swapped
over, i.e. SPOILER is controlled using the stick.
Study the table to locate the stick mode you wish to
use, then set the appropriate mode.
Page 20
concludes the process and
on the 3-D digi-adjustor now
on the 3-D digi-adjustor.
) MODE
SETUP
on