More Features Which Can Be Exploited With The Easy Model Type; Controlling V-Tail Models Menu: ( Mixer ) V-Tail; Deltas And Flying Wings Menu: Delta - Multiplex COCKPIX SX Manuel D'utilisation

Note: making the EXP effect visible on the model
EXP does not affect the centre point or end-points of
the control surfaces. If you wish to see the effect of
your settings on the model, you must hold the stick at
half-travel.
A brief press on the 3-D digi-adjustor concludes the
process. The value is now stored.
If you turn the 3-D digi-adjustor to the left, you can
leave this menu via "EXIT". Turning it to the right takes
you to the EXP settings for ELEVATOR and RUDDER.
AILERON (AI)
ELEVATOR (EL)
RUDDER (RU)
The EXP values for ELEVATOR and RUDDER are set
using the method described above for EXP A.
13.7. More features which can be ex-
ploited with the EASY model type
13.7.1. Controlling V-tail models
) V-TAIL
MIXER
Menu: (
At this point you can activate the pre-defined mixer for
a model with a V-tail.
The two servos for the V-tail must be connected to
receiver outputs 2 and 3.
2
The V-tail mixer can be assigned in any of eight differ-
ent ways: 1 to 4 and -1 to -4. This is necessary be-
cause the servos and control surface horns can be
installed in many different arrangements.
This makes it easier than ever before to set up a V-tail,
as it eliminates the need to reverse servos or swap
servo connections at the receiver.
Set "0" if your model has a cruciform (cross-) tail or a T-
tail.
The procedure for activating the V-LEIT mixer:
Action
Left to MENU
1.
Confirm
Right to MIXER
2.
Confirm
Right to V-LEIT
2.
Open V-LEIT
3.
for setting
EXP AI
EXP EL
EXP RU
3
Effect
SETUP appears
GAS>S4 appears
Operating Instructions
The current setting for the V-TAIL mixer flashes in the
bottom line of the screen.
Now proceed as follows:
a. Pull the ELEVATOR stick back, and hold it there.
b. Change the V-tail mixer mode from 1 to 4 using
the 3-D digi-adjustor until both control surfaces are
at the correct setting (up).
c. Move the RUDDER stick to the left and hold it
there.
d. If the control surfaces now operate in the wrong
direction, use the 3-D digi-adjustor to set the same
mode (1 to 4), but with "-" as prefix.
A brief press ( ) on the 3-D digi-adjustor concludes the
process, and the value is stored.
13.7.2. Deltas and flying wings
Menu: DELTA
Deltas and flying-wing models require a mixer which
superimposes the functions AILERON and ELEVA-
TOR, and passes the mixed travels to the two control
surfaces (servos 1 and 2).
1
Delta
left
4
Throttle
Caution: servos 1 and 2 are used
The servo assignment differs from the "usual" ar-
rangement for the EASY model type. If you activate
DELTA (value other than 0%), you must use receiver
outputs 1 and 2 for controlling the servos.
This arrangement makes it possible to use small, light-
weight four-channel receivers in deltas / flying wings.
The ELEVATOR signal is now present at receiver out-
put 5 instead of AILERON.
The magnitude of the AILERON travels is adjusted in
the MIXER menu under A -> A (
made here affect both control surfaces equally.
Page 27
SPOILER/
6
THR-LIMIT
PH
7
AUX 2
2 3
Rudder
Delta
5 Elevator
right
13.8.2.). Changes