Transmitter Controls For The Easy Type; Selecting Idle Forward / Back; Setup, Model ) Th R; Setting Throttle Check Menu - Multiplex COCKPIX SX Manuel D'utilisation

Stick mode table:
Mode left stick
1 Rudder Elevator Aileron Throttle
2 Rudder Throttle Aileron Elevator
3 Aileron Elevator Rudder Throttle
4 Aileron Throttle Rudder Elevator
5 Rudder Elevator Aileron
6 Rudder Spoiler Aileron Elevator
7 Aileron Elevator Rudder Spoiler
8 Aileron Spoiler Rudder Elevator
This is the procedure:
Action
Left to MENU
1.
Confirm
Confirm
2.
Confirm
3.
Open mode for set-
4.
ting
Use the 3-D digi-adjustor to select your preferred
mode, and confirm your choice with a brief press .
Note: idle trim
The trim button adjacent to the THROTTLE / SPOILER
stick is always used for throttle idle trim, even if the
right-hand slider is used to control throttle, as in modes
5 to 8.

Transmitter controls for the EASY type

13.3.3.
The picture below shows the functions of the individual
transmitter controls for the EASY model type.
Switch functions
Teacher button
Combi-Switch
Dual Rate
Slider functions
Flap (camber-changing flap)
right stick right
slider
Spoiler
Spoiler
Throttle
Effect
SETUP appears
MODEL appears
MODE appears
Emergency throttle OFF
(Throttle Cut)
not used
Servo 7
(Servo 4)
( 13.7.3)
Spoiler (modes 1 to 4)
or Throttle (modes 5 to 8)
Operating Instructions
13.3.4.

Selecting idle forward / back

Menu: (
The idle position of the transmitter control for throttle
(stick or slider) can be set to forward (towards the ae-
rial) or back (towards the pilot). When you set up a new
model, the setting is always
i.e. the idle position is "back".
Note: throttle servo / speed controller works in the
wrong "sense"
If you have decided on the idle position, but the power
system in your model runs to full-throttle at this setting,
you must reverse the throttle servo (
position must be left as it is, to ensure that THR-CUT (=
throttle cut = emergency motor OFF), throttle check (
13.3.5.) and the throttle / elevator mixer work correctly.
This is the procedure:
Action
Left to MENU
1.
Confirm
Confirm
2.
Right to TH
3.
Open TH
4.
for setting
"0" or "1" flashes in the bottom line.
THROTTLE R = "0" means:
the throttle idle position is back
THROTTLE R = "1" means:
the throttle idle position is forward
You can change the setting for THROTTLE R using the
3-D digi-adjustor. Press the 3-D digi-adjustor again to
end the process; the selected setting is then stored.
13.3.5. Setting Throttle Check
Menu: (
What is Throttle Check?
Throttle Check is a safety query of the throttle control.
This function avoids the danger of power systems
bursting into life unexpectedly, endangering and even
injuring you and others. It is a simple means of improv-
ing safety when operating any powered model.
How does Throttle Check work?
If the Throttle Check function is activated, the transmit-
ter checks whether the throttle control is at the idle
setting every time the transmitter is switched on, and
also when you switch to a different model memory. If
not, the screen continues to display the message
"GAS>0" until you move the throttle control to the idle
position. At the same time the throttle channel (receiver
output 4) is held at idle.
Page 21
) TH R
SETUP, MODEL
TH R = 0,
Effect
SETUP appears
MODEL appears
R
THROTTLE reverse
R
) TH CHK
SETUP, MODEL
). The idle