Siemens SINAMICS G130 Mode D'emploi page 1185

Masquer les pouces Voir aussi pour SINAMICS G130:
Table des Matières

Publicité

p1020
Fixed speed setpoint selection bit 0
[2505.3]
r1198.0
p1021
Fixed speed setpoint selection bit 1
[2505.3]
r1198.1
From
control word
setpoint
p1022
Fixed speed setpoint selection bit 2
channel
[2505.3]
r1198.2
p1023
Fixed speed setpoint selection bit 3
[2505.3]
r1198.3
<100> For SERVO, the following applies:
Only if the function module "extended setpoint
channel" is activated (r0108.8 = 1).
<101> Pre-assignment of the sampling times in p0115,
refer to p0112.
1
2
DO: SERVO, VECTOR, VECTOR3P, VECTORGL, VECTORM2C, VECTORMV, VECTORSL
Setpoint channel - Fixed speed setpoints
0.000
n_set_fixed 1 [rpm]
p1001[D] (0.000)
p1001[D]
n_set_fixed 2 [rpm]
p1002[D] (0.000)
p1002[D]
n_set_fixed 3 [rpm]
p1003[D] (0.000)
p1003[D]
n_set_fixed 4 [rpm]
p1004[D] (0.000)
p1004[D]
n_set_fixed 5 [rpm]
p1005[D] (0.000)
p1005[D]
n_set_fixed 6 [rpm]
p1006[D] (0.000)
p1006[D]
n_set_fixed 7 [rpm]
p1007[D] (0.000)
p1007[D]
n_set_fixed 8 [rpm]
p1008[D] (0.000)
p1008[D]
n_set_fixed 9 [rpm]
p1009[D] (0.000)
p1009[D]
n_set_fixed 10 [rpm]
p1010[D] (0.000)
p1010[D]
n_set_fixed 11 [rpm]
p1011[D] (0.000)
p1011[D]
n_set_fixed 12 [rpm]
p1012[D] (0.000)
p1012[D]
n_set_fixed 13 [rpm]
p1013[D] (0.000)
p1013[D]
n_set_fixed 14 [rpm]
p1014[D] (0.000)
p1014[D]
n_set_fixed 15 [rpm]
p1015[D] (0.000)
p1015[D]
3
4
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
n_set_fixed No act
r1197
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
5
6
Function diagram
fp_3010_51_eng.vsd
SINAMICS
16.10.13 V04.07.00
p0115[3]
<100>
<101>
n_set_fixed eff [rpm]
r1024
7
8
- 3010 -

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Sinamics g150

Table des Matières