Bosch RIESE & MULLER BDU330 Mode D'emploi page 41

English – 6
EN-76
Product Description and Specifications
Product Features
(9)
(13)
(12)
(11) (10)
(1) Display function button i
(2) Bike light button
(3) On-board computer
(4) Holder for on-board computer
(5) On/off button for on-board computer
(6) RESET button
(7) USB port
(8) Protective cap for USB port
(9) Operating unit
(10) Display function button i on the operating unit
(11) Decrease assistance level/scroll down but-
ton –
(12) Increase assistance level/scroll up button +
(13) Push assistance button WALK
1 270 U20 XBI | (07.04.2020)
(i)
(h)
(g)
(a)
TURBO
SPORT (b)
(f)
TOUR
ECO
(c)
OFF
MPH
KM/H
(e)
AMM
PMWH
MIN
MPH
KM/H
(d)
Range
(7)
(6)
(4)
(14) Locking mechanism for on-board computer
(15) Locking screw for on-board computer
USB charging cable (Micro A – Micro B)
A) Not depicted, available as an accessory
Display elements of on-board computer
(a) Drive unit assistance indicator
(b) Assistance level indicator
(c) Illumination indicator
(d) Text indicator
(e) Value indicator
(f) Speedometer
(g) Gear change recommendation: Higher gear
(h) Gear change recommendation: Lower gear
(i) Battery charge indicator
Technical Data
On-board computer
Product code
Max. USB port charging
current
(8)
USB port charging voltage
USB charging cable
Operating temperature
Storage temperature
(1)
Inserting and removing the battery
(2)
For inserting and removing the eBike battery in/from
the eBike, please read and observe the battery oper-
(3)
ating instructions.
Inserting and removing the on-board
(5)
computer
(14)
A)
(4)
(3) On-board computer
Prerequisites
The eBike system can only be activated when the fol-
lowing requirements are met:
– A sufficiently charged battery is inserted (see bat-
tery operating instructions).
Bosch eBike Systems Bosch eBike Systems
On-board computer
Intuvia Charging temperature
Internal lithium-ion bat-
BUI255
tery
mA 500
Protection rating
Weight, approx.
V 5
A) Not included with the product as standard
A) 1 270 016 360
B) When the USB cover is closed
°F +23 to +104
The Bosch eBike system uses FreeRTOS
°F +50 to +104
(see http://www.freertos.org).
Assembly
(4) Holder for on-board computer
(14) Locking mechanism for on-board computer
(15) Locking screw for on-board computer
To insert the on-board computer (3), slide it into the
holder (4) from the front.
To remove the on-board computer (3), push on the
locking mechanism (14) and slide it forwards out of
the holder (4).
When you park up the eBike, remove the on-
u
board computer.
(3)
The on-board computer can be secured in place to
(15)
prevent it from being removed from the holder. To do
this, remove the holder (4) from the handlebars. Put
the on-board computer in the holder. Screw the lock-
ing screw (15) (M3 thread, 8 mm long) from below
into the corresponding thread in the holder. Mount
the holder back on the handlebars.
Note: The locking screw is not designed to prevent
theft.
Operation
– The on-board computer is properly inserted in the
holder (see "Inserting and removing the on-board
computer", page English – 7).
– The speed sensor is connected properly (see drive
unit operating instructions).
English – 7
EN-77
Intuvia
°F +32 to +104
V 3.7
mAh 230
IP54
B)
lb 0.30
1 270 U20 XBI | (07.04.2020)