Table des Matières
Publicité
Unplug the spark plug connection from the spark
© Stanley Bostitch
plug. (Fig. 45)
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
7.
Using a 4mm hex key, remove and retain the hex
compliance for the products.
socket head bolts in the cylinder head. (Fig. 46) [M4
x 12, 4pcs]
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
8.
Gently lift the cylinder head away from the
rien que les produits soient conformes aux normes CE.
combustion chamber. (Fig. 47)
9.
Ensuring you do not damage the fan blades,
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
carefully remove the piston ring from behind the fan.
die CE-Richtlinien für Produkte.
(Fig. 48)
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
10. Using a dry cloth, clean and remove all deposits
zeggen dat de producten voldoen aan de CE-vereisten.
from the piston ring. (Fig. 49) Inspect the piston ring
for damage and if necessary replaces it [Part
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
No.192246]
produkterne.
11. Clean the cylinder head using brake cleaner, paying
particular attention to the spark plug. (Fig. 50)
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
12. A small brush may be useful to help release some
debris. You may need to repeat this 2 or 3 times until
clean. (Fig. 51)
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
13. Replace the piston ring on the cylinder head. (Fig. 52)
14. Lubricate the piston ring using Bostitch Gas Nailer
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
Lubricant [Part No. SB-20CL]. (Fig. 53)
conformità CE per i relativi prodotti.
15. Lubricate the hole which the motor shaft is set in
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
using Bostitch Gas Nailer Lubricant [Part No.SB-
merking for produktet.
20CL]. (Fig. 54)
16. Spray brake cleaner into the chamber to loosen any
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
residue. [SB-TC1] (Fig. 55)
conformidade com a CE para os produtos.
17. Using a blunt instrument [e.g. a screwdriver handle],
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
push down the piston. (Fig. 56)
conformidad con las normas CE de los productos.
18. Holding the tool Upside down, spray brake cleaner
into the cylinder, ensuring any residue falls back out
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
of the tool. You may need to carry out this operation
conformidad con las normas CE de los productos.
2 or 3 times, using a small brush to loosen some of
the more stubborn residue. (Fig. 57)
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
19. Using a screwdriver or a similar implement, push the
stanowią deklaracji zgodności CE prezentowanych produktów.
driver blade back into the tool. (Fig. 58)
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
Maintenance chart
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
ACTION
výrobky.
Clean magazine and feeder mechanism.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
Keep contact arm working properly.
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
20. Pull back the nail feeder to disengage the tool lock
21. Confirm that the piston ring is seated on the cylinder
22. Depressing the body, assemble the cylinder head
23. Put the 4 socket head bolts back to their original
24. Check the piston ring is correctly seated by pulling
25. Reconnect the spark plug lead wire and the the
26. Wrap the support (B) around the motor lead. (Fig. 66)
27. Fasten the screw using a screw driver. (Fig. 67)
28. Set the spark plug lead wire and the motor lead
29. Replace the top cover, ensuring neither of the leads
30. Replace the hex socket head bolt. (Fig. 70)
31. Always carry out 6-10 test cycles on an off-cut of
WHY
Prevent a jam.
Promote operator safety and
efficient Nailer operation.
out and press down the pushing lever on a hard
surface. Using Bostitch Gas Nailer Lubricant [Part
No. SB-20CL], oil round the outside groove in the
combustion chamber, where the lower piston ring
is located. (Fig. 59)
head; and then restore the cylinder head onto the
top of the tool ensuring that the wires are not
wedged therein. Take care not to damage the fan
blade. (Fig. 60)
and confirm the piston ring is not trapped. Set the 4
socket head bolts. (Fig. 61)
positions using a 4mm hex key. (Fig. 62)
back the nail feeder and depressing the pushing
lever. (Fig. 63)
motor lead.(Fig.64,65)
wire. (Fig. 68)
D: Confirm that the lead wires are inside the rib.
E: Confirm that the lead wires are not trapped by
cylinder head.
F: Confirm motor lead wire setting position.
is trapped. (Fig. 69)
timber before using on a finished surface, as
cleaning residue may be expelled. (Fig.71)
HOW
Blow clean daily.
Blow clean daily.
Publicité
Table des Matières
