Installation; Assembling The Equipment - Corghi Exact 70 Manuel D'utilisation

INSTALLATIoN

WARNING
Carry out the unpacking, assembly, lifting and
installation operations described with care.
Failure to comply with these recommendations
may damage the equipment and put the operator's
safety at risk.

Assembling the equipment

- Unpack the equipment, placing the packaging in
the position shown by the markings on it.
- Remove the monitor from its packaging (fig.3).
- Fit the monitor to the bracket provided (fig.4)
passing the power supply and signal cables
through the slot and secure all parts with the
screws supplied.
- Remove the rear panel of the lower cabinet.
- Take the aligner Sim Card (fig.52) and remove
it from its profiled support (keep the Sim Card
support, with serial number, for any future en-
quiries) and fit it into the slot provided (A, fig.53
with box open) with the gilded contacts facing
downwards and the chamfer towards the outside
of the reader (B, fig.53). Replace the front panel.
The reader can be fixed underneath the PC shelf
(A, fig.54) using the threaded rivets (B, fig.51) and
the screws provided, or it can be installed above
the PC later (B, fig.54).
- Unpack the personal computer (fig.6).
- Through the front door, place the computer on
the top shelf (fig.7).
For correct positioning, place the front part of the
computer level with the front of the shelf.
- Remove the printer from its packaging (A fig.8),
place it inside the cabinet and connect the power
supply and data cables after passing them through
the rear holes (fig.9).
- On radio version wheel aligners, fix the central
unit radio, supplied with the radio sensors, on
the cabinet using the connections provided (fig.5)
and use a sensor cable to connect it to one of the
cabinet sensor connectors (H fig.22).
52
Eichstädt Elektronik - Professionelle Kfz-Diagnosegeräte
http://www.eichstaedt-elektonik.de
- Connect the cables with the aid of the wiring
diagram (fig. 57); all the plugs are clearly marked
on their respective PC sockets. Press the plugs
fully down without applying too much force, and
tighten the safety screws where present (fig.9).
Note the differences in wiring, depending on
whether the smart card reader is installed inside
or outside the PC, as illustrated below.
- Connect the connector (fig.9) of the cables arriving
from the battery recharging housing to one of the
two connectors (fig.9) that emerge from the back
of the computer.
- Connect the sensor input cable to the reader's
male 9-pin D-Sub-connector marked "SENSOR"
(C, fig.55). Connect the reader's female 9-pin D-
Sub-connector marked "RS232" (B, fig.55) to serial
port COM1 of the PC using the cable provided.
Connect the remote control flat cable to the read-
er's 25-pin D-Sub-connector marked "REMOTE"
(A, fig.55). Connect the reader's USB connector
(D, fig.55) to one of the PC's USB connectors.
- The aligner is supplied set to operate on a power
supply of 230V AC. It can be set to operate on a
mains voltage of 115V AC. Position the PC voltage
change switch (switch marked D) as appropri-
ate.
- Replace the rear door using the spanner pro-
vided.
- The wheel aligner card supplied has already been
fitted in the Sim Card slot.
- Connect the power supply cable to the plug
provided; first read the "Electrical Hook-up"
section.
- Power up the PC, the monitor and the printer with
the switches provided.
- Upgrade the wheel aligner software if necessary,
"Updating the wheel Aligner Software" section,
and install any optional kits, "Installing Additional
Functions" section.
PC and cable output correspondence table:
PC and cables:
CONNECTOR CABLE TO
PC OUTPUT BE CONNECTED
COM 1 (**)
LPT 1 Printer cable
VIDEO Monitor cable
Operator's Manual EXACT 70
TYPE
D 9-pin
male
D 25-pin
female
D 15-pin
female