Logo; Customised Logo For Printout; Preparing The Vehicle For The Alignment Operation - Corghi Exact 70 Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

___If adjustable: Rear axle adjustment only acti-
vated if at least one of the angles that can be
measured is adjustable (half toe, camber, total
toe, setback).
Wheel Aligner Customisation
➥_ Electronic turntable enabling
___Always: electronic turntables for maximum steer-
ing angle always enabled.
___On request: electronic turntables for maximum
steering angle enabled on request during steer-
ing angle measurement.
___Never: electronic turntables for maximum steer-
ing angle never enabled.
➥_ Axis of reference
___Symmetry: axis of symmetry is axis of reference
for both front and rear.
___Thrust: thrust axis is axis of reference for both
front and rear. Setting the steering-wheel with
the front half toe values equal ensures the steer-
ing wheel will be straight in normal operating
conditions. If the thrust axis is axis of reference
for the rear axle, the rear half toe values area
always identical.
___Straight steering wheels: reference axis is axis
of symmetry for rear and thrust axis for front.
Setting the steering-wheel with the front half toe
values equal ensures the steering wheel will be
straight in normal operating conditions.
➥_ Save previous data
___Automatic: vehicle situation before adjustment
is saved automatically.
Manual: vehicle situation before adjustment is
saved in manual mode.
➥_ Caster measurement steering lock
___20°: Steering always locked to 20° for caster
measurement.
___User's choice: Caster measurement steering lock
at 10° or 20°.
➥_ Front axle adjustment
___Caster.
___Total toe – setback.
➥_ Rear axle adjustment
___Total toe – thrust angle.
___Setback – track difference.
70
Eichstädt Elektronik - Professionelle Kfz-Diagnosegeräte
http://www.eichstaedt-elektonik.de
➥_ Thrust angle
___Clockwise positive: angle is positive when thrust
axis is turned clockwise in relation to the axis of
symmetry.
___Anticlockwise positive: angle is positive when
thrust axis is turned anticlockwise in relation to
the axis of symmetry.

Logo

The logo is the image shown as background in the
"Main Menu" (fig.33) and used as three-dimensional
image in the screen saver.
2 customised logos can be entered: they are se-
lected from the set-up as the "Customised 1" and
"Customised 2" logos.
The customised logo files must be in bitmap format
and must have dimensions of 800x337 pixels.
Save the files in C: \ program files \ alignment
\graphics \ image\.
The file for the "Customised 1" logo is LogoFeF.bmp,
for the "Customised 2" logo it is LogoFew.bmp.

Customised logo for printout

The customer's logo can be added to the printed
job report.
Replace file C:\ Programs Files \Alignment\Graphics\
Image\IMGPrBarra4.bmp with an equivalent contain-
ing the logo of your choice.
Warning! The file dimensions must be 1100 x 354
pixels.
PrEPArING THE VEHICLE
For THE ALIGNmENT
oPErATIoN
For the wheel alignment operation to be carried
out correctly, all parts of the vehicle must conform
to the constructor's specifications; in particular, it is
important to check the tyre pressure and eliminate
any backlashes in the bearings and ball joints.
Place the vehicle over the pit or on the lift equipped
for the alignment operations, taking care to ensure
that the turntables and oscillating footboards are
locked in position.
Fit the self-centring clamp/sensor assembly on the
wheels and lock the clamp jaws onto the wheel rim
using one of the two handles.
CAUTION
Do not over-tighten the clamp as this may cause
it to bend.
Operator's Manual EXACT 70

Publicité

Table des Matières
loading

Table des Matières