Stryker SV2 Manuel D'utilisation page 8

• Always lock the bed extender before you place weight on the bed extender.
• Always retract the linen tray (option) before you put the product in motion.
• Always retract the linen tray (option) when not in use.
• Do not use the product for X-ray procedures if it does not have the radiolucent backrest (option).
• Do not use accessories to support patient limbs or other body parts.
• Do not clean, service, or perform maintenance while the product is in use.
• Always power off and unplug the power cord before cleaning, servicing, or performing maintenance.
• Always power off the product and unplug the power cord from the wall outlet when large spills occur near the circuit
boards, cables, and motors. Remove the patient from the product, clean up the fluid, and have service personnel inspect
the product. Fluids can cause unpredictable operation and decreased functionality of any electrical product. Do not
return the product to service until it is completely dry and has been thoroughly tested for safe operation.
• Do not spray cleaners directly onto the battery, control boxes, actuators, cables, or other electric equipment.
• Do not use abrasive powder, steel wool, or similar materials that may damage the product surface.
® ®
• Do not use V V i i r r e e x x TB for product disinfecting.
• Do not use acid-based chemicals or flammable chemicals, such as gasoline, diesel, or acetone for cleaning purposes.
• Do not directly spray or saturate the siderail control panel, patient control pendant, or nurse control pendant with
cleaners.
• The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
• Do not use sharp objects to clean the siderail control panel.
• Do not use V V i i r r e e x x ® ® T T B B for product cleaning.
C C A A U U T T I I O O N N
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.
• To minimize the risk of any electromagnetic interference, the product design follows the standard IEC 60601-1-2. To
avoid problems, use the bed in accordance with the EMC/EMI requirements in the EMC section of this operations
manual.
• Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should
be used no closer than 30 cm (12 in.) to any part of the SV2, including cables specified by the manufacturer. Otherwise,
degradation of the performance of this equipment could result.
• Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper
operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are
operating normally.
• Use of accessories, transducers, and cables other than those specified or provided by the manufacturer of this
equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this
equipment and result in improper operation.
• Do not place objects into any gaps of the product.
• Always plug the product into a wall outlet (regulated AC-power source) when not in use to maintain a sufficient battery
charge and to maximize product performance while operating on battery power.
• Always replace batteries that have corrosion at the terminals, display cracking, have expanded or bulging sides, or no
longer can maintain a full charge.
• Only use authorized batteries when replacing the batteries. Use of unauthorized batteries may lead to unpredictable
system performance.
• Do not place or store heavy objects on the product.
• Do not squeeze or pinch the power cord in the bed frame.
• Do not use the siderails as a push or pull device. Always move the product using the integrated handles in the
headboard and footboard.
• Always remove the patient lift pole before transporting the product.
• Do not use the IV pole as a push or pull device.
• Always make sure that the IV pole is at a low height during transport.
• Always apply the brake to prevent unintended movement.
• Do not apply the brake pedal to stop a moving product.
EN 4 KK-7500 REV 08