Preparation - TSM DURASWEEP 115 Mode D'emploi

1 1 1

PREPARATION

PREPARATION PREPARATION
1.1 1.1 1.1 Unpacking Unpacking Unpacking
After removing the outer packaging, remove the machine from the pallet; this operation can be done in two ways: After removing the outer packaging, remove the machine from the pallet; this operation can be done in two ways: After removing the outer packaging, remove the machine from the pallet; this operation can be done in two ways:
1. 1. 1. Take a hook and 4 tie-rods of suitable lifting capacity for the weight of the machine (shown on the CE plate). Lift Take a hook and 4 tie-rods of suitable lifting capacity for the weight of the machine (shown on the CE plate). Lift Take a hook and 4 tie-rods of suitable lifting capacity for the weight of the machine (shown on the CE plate). Lift
the motor bonnet and secure the four eyebolts or hooks in the threaded housings (the lifting hooks are inside the the motor bonnet and secure the four eyebolts or hooks in the threaded housings (the lifting hooks are inside the the motor bonnet and secure the four eyebolts or hooks in the threaded housings (the lifting hooks are inside the
collection bin Part. B FIG. 1 together with the side brushes and instruction manuals); secure all four straps to collection bin Part. B FIG. 1 together with the side brushes and instruction manuals); secure all four straps to collection bin Part. B FIG. 1 together with the side brushes and instruction manuals); secure all four straps to
their respective lifting hooks Part. A Fig. 1 and with the aid of a fork lift truck or bridge crane (suitable for weight their respective lifting hooks Part. A Fig. 1 and with the aid of a fork lift truck or bridge crane (suitable for weight their respective lifting hooks Part. A Fig. 1 and with the aid of a fork lift truck or bridge crane (suitable for weight
of the machine), lift this off the pallet and rest it on the floor very slowly. of the machine), lift this off the pallet and rest it on the floor very slowly. of the machine), lift this off the pallet and rest it on the floor very slowly.
ATTENTION: ATTENTION: ATTENTION:
THE MACHINE CAN ONLY BE LIFTED WHEN ALL FOUR STRAPS HAVE BEEN SECURED TO THEIR THE MACHINE CAN ONLY BE LIFTED WHEN ALL FOUR STRAPS HAVE BEEN SECURED TO THEIR THE MACHINE CAN ONLY BE LIFTED WHEN ALL FOUR STRAPS HAVE BEEN SECURED TO THEIR
RESPECTIVE EYEBOLTS (M10 EYEBOLTS). RESPECTIVE EYEBOLTS (M10 EYEBOLTS). RESPECTIVE EYEBOLTS (M10 EYEBOLTS).
2. 2. 2. Position a sloping surface (having a load-bearing capacity suitable for the weight of the machine) close up to the Position a sloping surface (having a load-bearing capacity suitable for the weight of the machine) close up to the Position a sloping surface (having a load-bearing capacity suitable for the weight of the machine) close up to the
narrow side of the pallet. This must be at least 1,5 m long (so as not to damage the rubber dust seals) and 1 m narrow side of the pallet. This must be at least 1,5 m long (so as not to damage the rubber dust seals) and 1 m narrow side of the pallet. This must be at least 1,5 m long (so as not to damage the rubber dust seals) and 1 m
wide. Remove the pieces of wood around the wheels and release the parking brake Part. 1 Fig. 2, pressing this wide. Remove the pieces of wood around the wheels and release the parking brake Part. 1 Fig. 2, pressing this wide. Remove the pieces of wood around the wheels and release the parking brake Part. 1 Fig. 2, pressing this
so as to release the retention lever. At this point, in the case of the E115 model, simply push the machine onto so as to release the retention lever. At this point, in the case of the E115 model, simply push the machine onto so as to release the retention lever. At this point, in the case of the E115 model, simply push the machine onto
the chute. This operation must be performed without anyone in front of the machine and on a large flat surface. the chute. This operation must be performed without anyone in front of the machine and on a large flat surface. the chute. This operation must be performed without anyone in front of the machine and on a large flat surface.
At the end of the unpacking operation, remove and keep the eyebolts and fit the right side brush Part. 7 Fig. 2 At the end of the unpacking operation, remove and keep the eyebolts and fit the right side brush Part. 7 Fig. 2 At the end of the unpacking operation, remove and keep the eyebolts and fit the right side brush Part. 7 Fig. 2
and, If necessary, the left side brush as shown in page 36. and, If necessary, the left side brush as shown in page 36. and, If necessary, the left side brush as shown in page 36.
IMPORTANT: ALL THE MATERIALS REMAINING AFTER THE UNPACKING OPERATION MUST BE IMPORTANT: ALL THE MATERIALS REMAINING AFTER THE UNPACKING OPERATION MUST BE IMPORTANT: ALL THE MATERIALS REMAINING AFTER THE UNPACKING OPERATION MUST BE
CAREFULLY DISPOSED OF BY THE USER, FOLLOWING APPLICABLE REGULATIONS. CAREFULLY DISPOSED OF BY THE USER, FOLLOWING APPLICABLE REGULATIONS. CAREFULLY DISPOSED OF BY THE USER, FOLLOWING APPLICABLE REGULATIONS.
ATTENTION: ATTENTION: ATTENTION:
MAKE SURE THAT THE MACHINE PROTECTION DEVICES ARE IN GOOD CONDITION AND MAKE SURE THAT THE MACHINE PROTECTION DEVICES ARE IN GOOD CONDITION AND MAKE SURE THAT THE MACHINE PROTECTION DEVICES ARE IN GOOD CONDITION AND
PROPERLY FITTED. IN THE EVENT OF FAULTS OR MISSING PARTS, DO NOT START UP THE PROPERLY FITTED. IN THE EVENT OF FAULTS OR MISSING PARTS, DO NOT START UP THE PROPERLY FITTED. IN THE EVENT OF FAULTS OR MISSING PARTS, DO NOT START UP THE
MACHINE AND NOTIFY THE DEALER OR MANUFACTURER MACHINE AND NOTIFY THE DEALER OR MANUFACTURER MACHINE AND NOTIFY THE DEALER OR MANUFACTURER
TSM - Technological Systems by Moro Srl TSM - Technological Systems by Moro Srl TSM - Technological Systems by Moro Srl
Via F.lli Zambon,9 - 33080 Fiume Veneto (PN) – Italy Via F.lli Zambon,9 - 33080 Fiume Veneto (PN) – Italy Via F.lli Zambon,9 - 33080 Fiume Veneto (PN) – Italy
Tel. +39.0434.564167 - Fax +39.0434.954069 Tel. +39.0434.564167 - Fax +39.0434.954069 Tel. +39.0434.564167 - Fax +39.0434.954069
www.tsmitaly.com – sales@tsmitaly.com www.tsmitaly.com – sales@tsmitaly.com www.tsmitaly.com – sales@tsmitaly.com
23 23 23
DURASWEEP 115 DURASWEEP 115 DURASWEEP 115
OPERATING MANUAL OPERATING MANUAL OPERATING MANUAL
V01 V01 V01