Fronius Vizor Connect Instructions De Service page 12

The helmet should only be recharged when a low charge status is displayed. To increase
the life of the battery, the battery should only be charged at temperatures below 45 ° C.
Note: DO NOT charge the helmet during work (power adapter, power bank, etc.)! If the helmet
does not darken when igniting the welding arc, check the charging status (press the grinding
button when the LED stops flashing blue, the battery is completely drained). If the anti-glare
cassette does not work properly despite the battery being charged, contact your local dealer.
A defective battery may only be replaced by the manufacturer or a Sercive certified by the
manufacturer.
Troubleshooting
ADF fails to darken
In Bluetooth® mode
→ Connect the helmet with the correct power source
Optical mode (Bluetooth® off)
→ Adjust the sensitivity (p. 6 no. I)
→ Clean the sensors or front cover lens
→ Switch off the opening delay - switch to "tack" for fast tack welding (p. 6 no. II)
→ Deactivate grinding mode (p. 7 no. V)
→ Charge Battery (p. 4 Nr. 1)
Protection level too bright
→ In manual mode, select a higher protection level (p. 7 no. IV)
→ In automatic mode, set the rotary knob to +1 or +2 (p. 7 no. III)
→ Replace the front cover lens (p. 4 no. 4)
Protection level too dark
→ In manual mode, select a lower protection level (p. 7 no. IV)
→ In automatic mode, set the rotary knob to -1 or -2 (p.7 No. III)
ADF flickers
→ Adjust the position of the opening time control (delay) to suit the welding process
(p. 6 no. II)
→ Adjust the sensitivity controller to suit the welding process (p. 6 no. I)
→ Charge the battery (p. 4 no. 1)
Poor visibility
→ Clean the front cover lens or ADF
→ In manual mode, adjust the protection level to suit the welding process (p. 7 no. IV)
→ In automatic mode adapt the protection level correction to suit the welding process
→ Increase the ambient light
(p. 7 no. III)
Welding helmet slips
→ Re-adjust/tighten the headband (p. 5 no. 3a- 3c)
Specifications (We reserve the right to make technical changes)
Protection level
UV/IR protection
Switching time from light to dark
Switching time from dark to light
Power supply
Weight
Operating temperature
Storage temperature
Classification according to EN379
Operating time with fully charged battery
Bluetooth® range
Channels and Frequencies
Transmission power
Radiated power
SAR
auto mode: 2.5 (light mode)
5 < 12 (dark mode)
manual mode: 2.5 (light mode)
7 - 12 (dark mode)
Maximum protection in light and dark modes
Pre-darkening in Bluetooth® mode.
Optical mode (Bluetooth® off):
90μs (23°C / 73°F)
70μs (55°C / 131°F)
0.1 - 2.0 s with "Twilight Function"
Solar cells, polymer Li-ion battery
550 g / 19.4 oz / PAPR 720 g / 25.4 oz
-10°C – 55°C / 14°F – 131°F
-20°C – 80°C / -4°F – 176°F
Optical class = 1
Scattered light = 1
Homogeneity = 1
Dependence on angle of view = 2
> 40h in Bluetooth®-Mode
20m in the open field
Channel 37 (2402 MHz)
Channel 38 (2426 MHz)
Channel 39 (2480 MHz)
<0.8mW
-2.5 dBm
not relevant Due to the large distance between
head and antenna and the low transmission
power of less than 0.8 mW (class 3)
Standards
Radio
Electromagnetic compatibility
Safety
Bluetooth®
Listings
Bluetooth® SIG DID
Bluetooth® Qualification
FCC
Approvals
Additional markings for PAPR
version
(notified body CE1024)
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides
information on the frequency bands used and the maximum RF transmit power of wireless
products for sale in the EU.
FCC / CNR conformity
This device complies with Part 15 of the FCC Rules and with Industry Canada license-
exempt RSS standard(s). Opteration is subject to the following conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interfernce
recieved, including interference that may cause undesired operation.
Radiofrequency radiation exposure Information
The radiated output power of the device is far below the FCC radio frequency exposure
limits. Nevertheless, the device should be used in such a manner that the potential for
human contact during normal operation is minimized.
Class B digital device
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to other devices, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reduce the separation between the equipment and receiver.
• Consult the dealer for help.
Declaration of conformity
See the Internet address on the last penultimate page.
Legal information
This document complies with the requirements of EU Regulation 2016/425 section 1.4
of Annex II.
Notified body
For detailed information see penultimate page.
Bluetooth® Trademark
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Fronius International GmbH is under license. Other
trademarks and trade names are those of their respective owners.
12
Bluetooth® Version: 4.2
2014/53 / EU
FCC
AS/NZS4268
ETSI EN 301 489-1
ETSI EN 301 489-17
IEC 62368-1: 2014 (2nd Edition) and Cor. 1: 2015
EN 62368-1: 2014 / AC: 2015 / A11: 2017
Bluetooth® Low Energy(CE) ETSI EN 300 328
Bluetooth® Low Energy(FCC) FCC - Title 47
CFR Part 15
RSS - Gen Issue 5
RSS - 247 Issue 2
D047959
RF-PHY.TS 5.0.3
FCC ID : 2ASFE-OPT-COM
IC : 24952-OPTCOM
HVIN: OPTCOM
PMN: OPTCOM
CE, compliance with CSA Z94.3, ANSI Z87.1,
AS/NZS 1337.1, AS/NZS1338.1
FCC (Note: see chapter "operating permit")
EN12941 (TH3 in combination with Fronius Vizor
Air/3 , TH2 for versions with hardhat and
, Air/3X
Fronius Vizor Air/3 ).
, Air/3X