Menu Overview - Spektrum BEAST X AR7210BX Mode D'emploi

EN

Menu Overview

SETUP MENU
(Menu-LED is steady ON )
A
Mounting orientation
B
Swashplate – servo frequency
Rudder – center position pulse
C
length
D
Rudder – servo frequency
E
Rudder – servo endpoints
F
Rudder – sensor direction
G
Swashplate – servo centering
H
Swashplate – mixer
I
Swashplate – servo directions
J
Swashplate – cyclic pitch geometry
K
Collective pitch range & endpoints
L
Swashplate – cyclic limit
M
Swashplate – sensor directions
N
RPM Governor – Operation mode
PARAMETER MENU
(Menu-LED is flashing quickly)
A
Cyclic and rudder trim/SAFE® trim
B
Control Behavior
C
Swashplate – Pitching up behavior
D
Tail – Rate Consistency
E
Stick deadband
F
Tail – RevoMIX
G
Cyclic response
H
Pitch boost
I
RPM Governor – Throttle response
J RPM Governor – Initial spool up rate
K
RPM Governor – Quick change rate
L
SAFE®– Operation mode
M
(SAFE® – Hovering pitch)
GOVERNOR MENU
(Menu LED flashing slowly)
A
RPM sensor – Function test
B
Throttle – Motor off/Idle position
C
Throttle – Full throttle position
D
Transmitter – Switch point display
E
RPM sensor – Divider
F
Main rotor – Gear ratio
G
(Sum of F + G + H if not
"user defined")
H
Purple Purple
OFF
Flashing Solid
horizontal vertical hor. inv.
socket, front socket, front socket, front
user defined
user defined
user defined
Use rudder stick to move servo to right endpoint and wait, then left endpoint and wait (or vice versa)
reference CH1 center
position position
mechanical
user defined
nor | inv | inv nor | nor | inv*
Use aileron stick to adjust 6° cyclic pitch on the roll axis to one direction (blades aligned with fuselage)
Set collective stick to max/min position and use aileron stick to adjust desired pitch.
Set pitch direction by rudder stick input: Status-LED blue = positive pitch, red = negative pitch
Move aileron, elevator and throttle stick. Adjust maximum limit by rudder stick input
inv | inv
deactivated*
Purple
OFF
Flashing
Use aileron and elevator stick to trim, hold button 2s to trim rudder. Reset all by rudder stick input.
Switch trim mode by activating SAFE® technology using the SAFE® switch channel.
user defined
user defined
user defined
user defined
user defined
user defined
user defined
user defined
user defined
user defined
deactivated* Bail out rescue
Purple
OFF
Flashing
"nitro" mode: Status-LED blue when magnet passes sensor "electric" mode: Status-LED red when motor is running
"nitro" mode: throttle servo to (increased) idle position "electric" mode: throttle in "motor off" position, just before motor starts
Set throttle channel/throttle servo to full throttle position
RPM
Governor off
1 2
8
user defined
+0.00 +0.20
+0.00 +0.05
Red Red
Flashing Solid
vert. inv. horizontal
socket, front socket, back
50 Hz* 65 Hz 120 Hz
960 μs 760 μs
50 Hz* 165 Hz 270 Hz
normal*
CH2 center
position
90° 120°*
nor | inv | nor
inv | nor nor | inv
electric
Purple Red
Solid Flashing
normal sport*
very low low
very low low
very small small*
off* low - nor
normal* slightly increased
off* low
normal slightly increased
50 RPM/s 100 RPM/s
as initial rate 300 RPM/s
Bail out rescue
3D - Mode
with pitch
Adjust by aileron stick input. Reset by rudder stick input.
Purple Red
Solid Flashing Solid
RPM
Governor
Governor on
maximum
3* 4
9* 10
+0.40* +0.60
+0.10* +0.15
54
Blue
Blue
Flashing
Solid
vertical hor. inv.
socket, back socket, back
165 Hz 200 Hz
1520 μs*
333 Hz (560 Hz)
reversed
CH3 center
position
140° 140° (1=1)
nor | nor | nor
nor | nor*
nitro
Red
Blue
Flashing
Solid
pro extreme
medium* high
medium* high
medium large
high - nor low - rev
increased high
medium high
increased fast
200 RPM/s 300 RPM/s
500 RPM/s 700 RPM/s
3D - Mode with
pitch
Red Blue
Blue
Flashing
Solid
RPM
RPM
Governor
autorotation
5 6
11 12 13
+0.80
Red/
Blue
vert. inv.
socket, back
*Factory setting
Blue
Solid
transmitter
very high
very high
very large
high - rev
very high
very high
aggressive
400 RPM/s
900 RPM/s
Flight trainer
mode
Red/
Blue
7
14