Scheppach 5901403903 Traduction Des Instructions D'origine page 31

• Have the device checked if necessary.
• Switch the device off if it is not in use.
Suitable saw blades
All industry-standard saw blades with a minimum
length of 127 mm with and without a pin may be used.
7. Before commissioning
7.1 Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of the
warranty period.
m WARNING
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
¿ O PVRUVPDOOSDUWV There is a danger of choking
or suffocating!
7.2 General notes
• Prior to commissioning, all covers and safety devic-
es must be mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that the
saw blade is correctly fitted, and that moving parts
run smoothly.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Only connect the machine to a correctly installed
protective contact socket, with fuse protection of at
least 10 A.
7.3 Install the scroll saw on the workbench
You require the following for assembly:
• M8 hexagonal bolt (4x)
• M8 hexagonal nut (4x)
• Washer Ø 8.4 mm (8x)
(not included in the scope of delivery)
The length of the screws to be used vary depending on
the thickness of the tabletop.
m WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
1. Mount the scroll saw on a solid wooden work-
bench. This way, a high noise level due to vibra-
tions can be avoided.
2. Mark the drill holes (see fig. 5.2).
3. Drill the 4 holes (diameter 8 mm) into the work-
bench.
4. Screw the scroll saw onto the workbench with the
hexagonal bolt (E) through the assembly points
(fig. 3 pos. 19) in the following sequence (fig. 5.1):
D Hexagonal nut
C Washer
A Scroll saw
B Workbench
C Washer
E Hexagonal bolt
5. Tighten the hexagonal nuts (D).
8. Layout
m WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
8.1 Installing the saw blade guard (5) and the re-
WDLQ L Q J GHYLFH¿ J
NOTE:
Before assembling the retaining device (23), the saw
blade pre-installed at the factory (21) must be removed
(see 8.2).
1. Remove the saw blade (21) as described in 8.2.
2. Remove the retaining device (23) from the saw
blade guard (5): Loosen the screw (24) complete-
ly using a Phillips screwdriver (not included in the
scope of delivery) (see fig. 6).
3. Insert the holder (4) into the opening (see fig. 7).
4. Fasten the holder (4) with the knurled screw (3).
5. Mount the retaining device (23) to the saw blade
guard (5). Insert the screw (24) into the holder (4).
Tighten the screw (24) using a Phillips screwdriver
(not included in the scope of delivery).
6. Insert the saw blade (21) again as described in 8.2.
7. Ensure that the retaining device (23) does not
touch the saw blade (21).
www.scheppach.com
GB | 31