Hendi 210000 Manuel De L'utilisateur page 15

• blade guard
• ring
• blade cover
• meat pusher
• meat pusher knob with ring nut and spacer
• hand cover on the food tray
Electrical safety system
The appliance is equipped with:
• a micro-switch which stops the appliance in case the tie rod
for blade guard is removed; the micro-switch prevents from
restarting the appliance if the guard has not been set in the
switch-off position.
• a relay in the control box which requires the restart of the
appliance when a power cut occurs.
Even though CE version appliance are provided with electrical
and mechanical protections (when the appliance is operating
and for maintenance and cleaning operations), there are still
RESIDUAL RISKS that cannot be eliminated completely; these
risks are specified in this manual under "WARNING! / DAN-
GER! / CAUTION!". The blade and other parts of the machine
can cause cuts and injuries.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Installation or Assembly & Disassembly
The assembly or disassembly operations of the appliance are
performed with the appliance stopped and disconnected from
the power supply.
ATTENTION! Any installation, maintenance and repair work
should be performed by qualified and authorized technician
only.
Sharpener (Fig.5 on page 6)
1. Attach the sharpening module in such as way that the blade
does not move between the wheels.
2. Secure the sharpening device to the machine by tightening
the holder. Check to make sure that the sharpening device
is well secured before using the machine.
NOTE! The sharpening device is equipped with a safety switch.
If the sharpening device is not properly attached, you will not
be able to use the appliance.
Hand guard (Fig.6 on page 6)
1. Place both screws in the carriage.
2. Attach the hand guard.
3. Place the two washers over the white bolts.
4. Screw on the two dome nuts.
NOTE! You are advised not to use the appliance if the hand
guard is not attached as instructed! These are safety features
that will prevent possible injury. If you do not attach these fea-
tures, there will be a risk of injury.
Operating instructions
The appliance must be installed upon a working table suita-
ble for it's overall dimensions shown in "Technical specifica-
tions"; therefore, it must be adequately large, well leveled, dry,
smooth, resistant, stable and placed at a height of 80 cm from
the ground.
Moreover, the machine must be installed in a room with max.
humidity of 75% at the temperature between 5°C and 35°C, that
is in the environment which does not contribute to the appli-
ance failure.
IMPORTANT! All parts(meat pusher, hand cover, blade sharp-
ener) must be installed, assembled and secured before op-
eration.
• Position the appliance so that the on/off switch is facing the
user.
• If the blade sharpener has not been installed, proceed as
follows:
- Position the blade sharpener in its support so that the blade
does not extend between the gears.
- Tighten the safety screw on the blade sharpener.
- Note! The appliance is equipped with a safety switch and will
turn off automatically if the sharpening device is removed)
• Push the plug in the wall socket.
• Turn the dial with the graduated scale to the desired slice
thickness.
• Switch ON the appliance by pressing the "WHITE (I)" button
of the ON/OFF switch.
• Put the food product on the carriage and adjust the clamp
to hold the product firmly in place. Make sure the product is
positioned against the stop plate.
• Once the product has been sliced, switch OFF the appliance
by pressing the "BLACK (O)" button of the ON/OFF switch.
• Turn the thickness dial back to "0".
How to lock the slicer
(Fig 7 on page 6)
1. Turn the knob in anti-clockwise direction.
2. Continue to turn the knob until it is loosen completely.
3. Move the carriage to the proper position, the slicer will be
locked automatically.
How to unlock the slicer
(Fig 8 on page 6)
Turn the knob in clockwise direction to unlock the slicer. The
knob should be turned completely to tighten the carriage.
GB
15