Hendi 210000 Manuel De L'utilisateur page 17

The blade is to be removed as follows (see Fig.17 on page 8):
• disassemble the blade guard;
• remove the sharpener (a) and move the blade out of blade
ring guard by turning the thickness dial knob;
• loosen the 3 or 4 screws (15) (according to the model) that
fix the blade;
• Take out the blade directly.
WARNING! Pay attention to residual risks due to cutting and/
or sharp edges. Wear protective gloves (not supplied).
The blade guard must be cleaned with hot water and neutral
detergent.
Sharpener cleaning
• The sharpener cleaning operation is carried out by rubbing
the grinding moles with a brush. The moles must be placed
in the safety position which means that they must be turned
towards the side opposite to the blade.
Deflector cleaning
• To remove the deflector, unscrew the two screws (16) of the
deflector (see Fig.18 on page 8).
• Clean the deflector with hot water and neutral detergent.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
• Place the thickness dial knob adjusting the thickness plate
in the "0"position.
• Please call the manufacturer or its services agent for any
replacement.
Belt
The belt is not to be adjusted. It must be replaced after 3 or
4 years.
Feet
Feet may deteriorate and lose elasticity, thus reducing the sta-
bility of the appliance. In this case they must be replaced.
Power supply cord
Periodically check the power supply cord for any symptoms of
worn-out. In this case it must be replaced.
Blade
Check that the blade does not lose more than 10mm of its orig-
inal diameter. In this case it must be replaced.
Sharpener - grinding moles
Check that the grinding moles retain their abrasive property
during sharpening operations. If not, it must be replaced to
prevent the blade damage.
Lubrication of sliding guides
From time to time pour some oil drops onto the round sliding
guide along which the carriage moves back and forth. This op-
eration can be performed through the opening (OIL) next to the
thickness dial knob.
Label of the ON/OFF switch
If the labels of the ON/OFF switch have been damaged, in this
case it must be replaced.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• Special care must be taken when moving or transporting the
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem Possible cause
Appliance Blunt blade
does not
Dirty appliance
slice evenly
Appliance Overheated
stops slicing motor
Carriage Dirty slide bar
does not
slide
Some food stick
to the blade.
Blade v-belt worn
stops when out or dirty
product is
being cut
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Possible solution
Sharpen blade
Clean the appliance
Let the machine cool off
for an extended period. The
motor's safety thermostat will
reset itself automatically.
Clean the slide bar and
lubricate with Vaseline
Switch off the appliance
& unplug it. Let it come to
a complete stop. Remove
any blockage. Wipe the
blade with a damp cloth.
Contact the supplier.
17
GB