Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
CLEANING AND CARE
Before performing any cleaning and
Read the general safety information about
Z
X
cleaning in the chapter "safety information".
Turn the oven off.
Z
X
– Depending on how the oven is installed:
Unplug the oven or disconnect the power at
the main electrical system switch, e.g., switch
off the fuse of the oven in the fuse box.
General recommendations
Stains on the base of the oven from various cooking
products (sauces, sugar, proteins and fat) are always
caused by spills and splashes. Splashes occur during
cooking and are usually the result of cooking at too
high temperatures. Spills occur when using cooking
dishes which are too small, or due to an incorrect
estimate of increases in volume during cooking.
These problems can be avoided by using deep
cooking receptacles or by using the enamel trays
supplied with the oven.
The stainless steel and enamelled parts of the oven
will remain as good as new if cleaned regularly with
water or special detergents.
Ensure that the oven is cold before you start
Z
X
cleaning.
Do not use steam cleaners or direct jets of water.
Z
X
Do not use coarse abrasive materials or sharp metal
Z
X
scrapers to clean the glass parts of the oven door.
They could scratch the surface and cause the glass
to shatter.
Never use scouring pads, steel wool, muriatic acid
Z
X
or other products which could scratch or mark
the surface.
Only use hot water and non-abrasive detergents
Z
X
when cleaning the enamelled surfaces and the
oven chamber.
Use a branded glass cleaner for the glass.
Z
X
Using the auto clean function
This function is only available on ovens with pyrolitic
cleaning function, like FS913P.
The AUTO CLEAN function turns oven cleaning into
a quick, easy and instant procedure. The temperature
reached in the cooking compartment (450°C)
carbonizes all food and fat residue. During this process,
some particles of residue may glow; this is a normal
phenomenon due to instantaneous combustion.
FS 913 M / FS 913 P
If the AUTO CLEAN function is activated, the oven
care:
door is locked after the first two minutes cycles and
cannot be opened. The padlock icon lights up.
The obscuring of the LCD display during the pyrolitic
cleaning process is a precautionary display protection
feature caused by the high temperatures in use.
We recommend to start the cleaning cycle always
with room temperature oven.
Before cleaning
Accessories left in the oven may hinder the
correct circulation of heat on all the walls or may
be damaged due to the high temperatures.
Remove all accessories (enamel trays, racks,
Z
X
runners, telescopic guides).
Do not leave anything inside the oven.
Z
X
Remove food residues using a moist sponge.
Z
X
Never use detergents or any other specific
Z
X
cleaning product.
Do not obstruct the circulation of air in the area in
Z
X
front of the oven.
Do not leave anything on the door handle.
Z
X
The surfaces may become very hot during
pyrolytic cleaning process.
Keep children away.
Z
X
Clean the internal glass panel with a mixture of
X
X
water and soap.
Start the AUTO CLEAN function at the display.
X
X
After cleaning
Clean the internal glass panel with a glass cleaner.
X
X
Dry all parts of the oven thoroughly after cleaning.
X
X
Cleaning the oven chamber
It is easier to remove any stains while the oven is still
warm and while the stains are still new.
Ensure the oven is cool to the touch, to avoid
Z
X
burns.
Clean the enamelled surfaces and the oven chamber
X
X
with hot water and non-abrasive detergents.
Dry all parts of the oven thoroughly after cleaning.
X
X
Cleaning the oven door
Ensure that the oven is cold before you start
Z
X
cleaning.
To facilitate oven cleaning, the oven door can be
removed (see chapter „Removing the oven door").
– 30 –
Publicité
Chapitres
Table des Matières
