Siemens SINUMERIK 828D Mode D'emploi page 161

Index
$
$A_INA, 77
$AA_AXCHANGE_STAT, 94
$AA_AXCHANGE_TYP, 94
$AA_JERK_COUNT, 48
$AA_JERK_TIME, 48
$AA_JERK_TOT, 48
$AA_OFF, 51
$AA_OFF_LIMIT, 52
$AA_OVR, 42
$AA_PLC_OVR, 42
$AA_TOFF, 54
$AA_TOFF_VAL, 55
$AA_TOTAL_OVR, 43
$AA_TRAVEL_COUNT, 48
$AA_TRAVEL_COUNT_HS, 48
$AA_TRAVEL_DIST, 48
$AA_TRAVEL_DIST_HS, 48
$AA_TRAVEL_TIME, 48
$AA_TRAVEL_TIME_HS, 48
$AC_BLOCKTYPE, 58
$AC_BLOCKTYPEINFO, 58
$AC_DTEB, 82
$AC_FCT0, 49
$AC_FCT1, 49
$AC_FCT2, 49
$AC_FCT3, 49
$AC_FCTLL, 49
$AC_FCTUL, 49
$AC_FIFO, 36
$AC_MARKER, 30
$AC_OVR, 41
$AC_PARAM, 31
$AC_PLC_OVR, 42
$AC_SPLITBLOCK, 60
$AC_SYNA_STATE, 64
$AC_SYNC_ACT_LOAD, 44
$AC_SYNC_AVERAGE_LOAD, 44
$AC_SYNC_MAX_LOAD, 44
$AC_TANEB, 41
$AC_TIMER, 34
$AC_TOTAL_OVR, 43
$AN_IPO_ACT_LOAD, 43
$AN_IPO_LOAD_LIMIT, 45
$AN_IPO_LOAD_PERCENT, 43
$AN_IPO_MAX_LOAD, 43
$AN_IPO_MIN_LOAD, 43
Actions synchrones
Description fonctionnelle, 07/2023, A5E48765042D AF
$AN_SERVO_ACT_LOAD, 43
$AN_SERVO_MAX_LOAD, 43
$AN_SERVO_MIN_LOAD, 43
$AN_SYNC_ACT_LOAD, 43
$AN_SYNC_MAX_LOAD, 43
$AN_SYNC_TO_IPO, 43
$P_TECCYCLE, 121
$SA_WORKAREA_MINUS_ENABLE, 46
$SA_WORKAREA_PLUS_ENABLE, 46
$SN_SW_CAM_MINUS_POS_TAB_1, 46
$SN_SW_CAM_MINUS_POS_TAB_2, 46
$SN_SW_CAM_MINUS_TIME_TAB_1, 46
$SN_SW_CAM_MINUS_TIME_TAB_2, 46
$SN_SW_CAM_PLUS_POS_TAB_1, 46
$SN_SW_CAM_PLUS_POS_TAB_2, 46
$SN_SW_CAM_PLUS_TIME_TAB_1, 46
$SN_SW_CAM_PLUS_TIME_TAB_2, 46
A
Action synchrone à effet non modal, 20
Action synchrone modale, 20
Action synchrone statique, 20
Actions synchrones
Adaptation additive via SYNFCT, 74
Exemple : Presses, couplages d'axes, 142
Exemple : Régulation AC, 135
Exemple : Régulation de l'avance tangentielle, 136
Exemple : Régulation par correction
dynamique, 137
Arrêt CN, 126
AXTOCHAN (SA), 92
C
CANCEL, 123
CANCELSUB, 116
Combinaisons booléennes, 23
CP..., 110
Cycle technologique, 24
Cycles technologiques, 117
D
DELDTG, 83
DO, 24
161