Starting Up Again; Disposal; Maintenance - salmson Rocsan evo Installation Et Mise En Service

English
BEWARE of poisonous substances!
Products that pump fluids which are hazardous
to health must always be decontaminated before
undertaking any other work. There is otherwise a
risk of fatal injury! Wear the necessary protective
clothing for this work.
BEWARE of burns!
The housing components can heat up to well above
40 °C. There is a danger of burns! After switching
off, let the product cool down to ambient tempera-
ture.
7.2.1. Removal
Portable wet installation
Products in portable wet installations can be lifted out of the pit
after being disconnected from the mains power supply and emp-
tying the discharge pipe. You may have to disconnect the hose
first. The use of appropriate hoisting gear may be necessary.
Stationary wet installation
Products in stationary wet installations with suspension units are
raised out of the pit using appropriate lifting gear. During lifting,
always hold the power cable slightly taut to prevent it from being
damaged.
The operating area does not have to be emptied especially for
this purpose. The shut-off valves in the intake and discharge pipe
must be closed to prevent the operating area from overflowing or
the discharge pipe from being emptied.
7.2.2. Return delivery/storage
Return delivery
For shipping, the parts must be packed and sealed in sufficiently
large, non-tearing plastic sacks to prevent leakages. Shipping
must be carried out by carriers who have been briefed accordingly.
Please also refer to the "Transport and storage"
section.
Storage
• Clean the pump thoroughly, decontaminating it if neces-
sary.
• Store it in a clean, dry place protected from frost.
• Place it down vertically onto a firm foundation and secure
it against falling.
• Seal the intake and discharge ports tight with suitable
material (such as foil).
• Support the power cables at the cable lead-in to pre-
vent permanent deformation and protect the ends from
moisture.
• Protect the pump from direct sunshine to prevent the
elastomer parts and housing coating from becoming
brittle.
Please also refer to the "Transport and storage"
section.
7.3.

Starting up again

Clean the product of dust and oil deposits before starting up
again. Then carry out all the maintenance tasks as described
in the "Maintenance" section.
Once this work has been completed, the product can be installed
and connected to the electricity supply by an electrician. This
work must be carried out in accordance with the "Installation"
section.
The product must be switched on as described in the "Start-up"
section.
The product may only be restarted if it is in perfect
condition and ready for operation.
7.4.

Disposal

7.4.1. Lubricants
Oils and lubricants must be collected in appropriate containers
and properly disposed of in terms of EC Directive 75/439/EEC as
well as in compliance with the provisions of sections 5a and 5b
of the German Waste Act or the applicable local laws.
7.4.2. Protective clothing
Protective clothing worn for cleaning and maintenance work is to
be disposed of in accordance with the German Waste Code TA 524
02 and EC Directive 91/689/EEC.
7.4.3. Product
Proper disposal of this product avoids damage to the environment
and risks to personal health.
• Make use of the services or the advice of public or private
waste disposal companies for the disposal of the product
or parts of it.
• More information about proper disposal can be obtained
from the urban administration, the waste disposal au-
thorities or from the supplier from whom the product was
purchased.
8.

Maintenance

Before performing maintenance or repair work, switch off and
dismount the product as described in the section entitled "Final
shutdown/disposal".
After completing maintenance or repair work, the product must
be installed and connected according to the "Installation" section.
The product must be switched on as described in the "Start-up"
section.
Maintenance or repair work must be carried out by an authorized
service center, Salmson customer service or a qualified specialist.
Maintenance or repair work and/or constructional
changes that are not listed in this operating and
maintenance manual or which could impair explosion
protection, may only be carried out by the manufac-
turer or by authorized service centers.
The spark-proof gaps may only be repaired according to the man-
ufacturer's design specifications. It is not permitted to carry out
repairs according to the values in tables 1 and 2 of DIN EN 60079-
1. Only the screws stipulated by the manufacturer, fulfilling at
least strength category A4-70, may be used.
51