Angelo Po BX61E Manuel D'utilisation page 36

7) Time setting button (Timer)
– To set the cooking time: press once (the green light fl ashes) to set the cooking time using the
knob (10). Keep the button pressed for about 2 seconds to set an "unlimited" cooking time; the
display (12) shows the message "InF", which cannot be modifi ed.
– To modify the time during cooking: press once to display the value of the time set on the di-
splay (12).
Press the button and turn the knob (10) to modify the value set.
– Enable or disable the automatic preheating.
With the appliance in the STOP phase (green light (2) on) press the button and hold it down for
longer than 3 seconds (the whole panel powers down). Press and hold the button (7) and turn
the knob (10) to enable or disable the automatic preheating.
Press the button (7) to confi rm the changes made.
8) Humidity percentage setting button
– Sets the humidity percentage in mixed cooking mode (convection + steam).
Press button once (the green light fl ashes) and set the percentage of humidity using the knob
(10).
– To modify the percentage of humidity during cooking: press once to display the value of the
humidity on the display (13).
Press the button and turn the knob (10) to modify the value set. Wait about 5 seconds for the
new value set to be saved.
In "convection cooking" mode you can adjust the percentage of opening of the vent ,
which is shown on the display (13) ("0" = vent always open; "_._" = vent always closed).
– Increases the percentage of humidity: keep the button pressed to introduce humidity inside the
oven during any mixed or convection cooking phase.
– While cooking in "steam cooking" mode, this switches from standard (Std) steam to super (Sup)
steam and vice-versa.
– To set the default value between Std and Sup steam: With appliance in STOP phase (green in-
dicator light (2) on) press the button (14) longer than 3 seconds (the entire panel switches off ).
Keep the button (8) pressed and act on the knob (10) to select Std or SUP. Press the knob (10)
to confi rm the change made.
9) Product core probe or "vacuum" temperature setting button"
– Sets the cooking temperature inside the product: measured by the core probe (optional) or with
vacuum (optional); press once (green light fl ashes) to set the temperature using the knob (10).
– Modifi es the temperature inside the product during cooking: press once to show the tempera-
ture value on the display (12).
Press the button and turn the knob (10) to modify the value set.
Wait about 5 seconds for the new value set to be saved.
GB
This function disables use of the "Time setting" button (Timer).
10) Control knob
– For varying the values of the functions selected (see buttons 6, 7, 8, 9).
Turn the knob clockwise to increase the value and anti-clockwise to decrease it.
– Used to modify the cooking and washing programming parameters and the appliance's functio-
nal parameters.
– Also confi rms and saves: press the knob to confi rm and save the settings selected and/or shown
on the display.
11) Temperature display
– Shows the value of the temperature set.
To display the real temperature inside the oven, keep button (6) pressed until the display shows
the dot in the lower right.
The value on the display fl ashes at the start of a cooking process when the temperature inside
the oven is higher than the temperature set and/or during preheating when the set temperatu-
re has not been reached.
– During a pause in cooking, it shows the number of the "Regeneration" program available for
selection using button (15).
12) Time and "product core probe" display
With button (7) (timer) pressed:
– In cooking pause status it shows the value of the time set.
– During cooking it shows the time left to the end of the cooking cycle.
3326460_ut_GB_rev.2
- 8 -
ENGLISH