Kärcher KM 105/100 R Bp Mode D'emploi page 38

Troubleshooting by the operator with plain text messages on the display
Note:
If the display messages shown remain despite the corrective measures described, contact service!
Display
1 Invalid KiK!
Operation locked
2 Valid KiK but no
operation rights
3 High dump tracer
stuck! Check it!
4 Locked HD-tracer
5 Sit on machine
for operation!
7 Dirt pan open!
8 Dirt pan open?
9 Brushpos. not ok
10 RBroompos.not ok Is displayed when the right side brush cannot move to
11 LBroompos.not ok
38
Meaning and consequence
The identification of the inserted key is unknown.
– The appliance operation is prevented
The KIK-key (Kärcher Intelligent Key) is known, howev-
er not approved for this appliance.
– The appliance operation is prevented
The function of the two-hand operation button is
checked for its safety function when the appliance is
switched on.
– When the two-hand operation button is pushed, the
operation is prevented during start-up
The two-hand operation button (high emptying system)
was pushed in a sweeping programme.
– High emptying is prevented in the sweeping pro-
gramme for safety reasons.
Appears when a sweeping or transport programme is
selected upon starting up the machine and no operator
is sitting on the seat.
– All unit functions are prevented
Is displayed (low emptying system) as soon as a trans-
port or sweeping programme has been selected and at
least one waste container is removed.
– All unit functions are prevented
Is displayed (high emptying system) as soon as a
sweeping programme has been selected and the waste
container is not fully retracted and tipped inwards.
– All sweeping functions are prevented.
Note: In case of an attempt to completely lower a con-
tainer that is tipped outwards, a collision monitoring sys-
tem prevents the high emptying system from being dam-
aged
Note: In case of an attempt to tip a retracted container
outwards, a collision monitoring system prevents the
high emptying system from being damaged
Is displayed when the roller brush cannot move to the
factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying
the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the right side
brush may not be raised
Is displayed when the optionally available left side brush
cannot move to the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the left side
brush may not be raised
Corrective measures
 Insert approved KIK-key (Kärcher Intelligent
Key)
 Insert approved KIK-key (Kärcher Intelligent
Key)
 Programme the key with the Supervisor Intelli-
gent Key.
 Release the two-hand operation button.
 Confirm the message with the OK key (delete).
 Release the two-hand operation button.
 Turn the programme selector switch to position
C (drive).
 Press the two-hand operation button and keep it
down.
 Operate the high emptying system by means of
the direction keys.
 Sit on the driver's seat.
Note: The selected sweeping / transport opera-
tion starts fully automated.
Note: This procedure simultaneously serves the
inspection of the safety function of the seat
switch!
 Lock all waste containers in place.
 Turn the programme selector switch to "ON".
Note: The message disappears. The appliance
is ready for operation.
 Turn the programme selector switch to position
C (drive).
 Press the two-hand operation button and keep it
down.
 If necessary, tip the waste container inwards
and then lower it by means of the direction keys.
 Release the two-hand operation button and the
direction keys.
 Press the two-hand operation button and keep it
down.
 Completely tip the container inwards by means
of the direction keys before lowering it.
 Release the two-hand operation button and the
direction keys.
 Press the two-hand operation button and keep it
down.
 Sufficiently raise the container by means of the
direction keys before it can be tipped outwards.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
16
-
EN