Kärcher KM 105/100 R Bp Mode D'emploi page 36

 Insert new roller brush half and tighten
the screws.
 Then ensure that the roller brushes are
safely locked in place.
With appliance with low emptying sys-
tem:
 Reattach the centre bar, ensure proper
seating of the gaskets!
Adjusting and replacing sealing strips
 Park the machine on an even surface.
 Turn the programme selector switch to
"OFF" and remove the KIK-key.
Side brush and roller brush are raised.
5
4
2
1
15-20 mm
1 Front sealing strip
2 Nut
3 Retaining plate front
4 Rear sealing strip
5 Screw
6 Forward travel direction
 Front sealing strip
Adjusting the sealing strip:
 Loosen the nuts by approx. 2 rotations,
do not completely unscrew them.
 Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 80-85 mm.
 Tighten nuts.
If worn, replace.
 For replacing the sealing strips unscrew
the nuts completley, insert new sealing
strip, fit retaining plate, adjust sealing
strips and screw down retaining plate.
 Rear sealing strip
Adjusting the sealing strip:
 Loosen screws by approx. 2 rotations,
do not completely unscrew them.
 Set the distance between the sealing
strip and the floor so that it tilts towards
the front with an overtravel of 15 -
20 mm.
 Tighten the screws.
If worn, replace.
 For replacing the sealing strips unscrew
the screws completley, insert new seal-
ing strip, fit retaining plate, adjust seal-
ing strips and screw down retaining
plate.
 Side sealing strips
Adjusting the sealing strip:
 Loosen screws by approx. 2 rotations,
do not completely unscrew them.
 To set the floor clearance, insert a
sheet with a thickness of between 1 and
3 mm under the sealing strip.
 Adjust sealing strip.
 Tighten the screws.
If worn, replace.
 For replacing the sealing strips unscrew
the screws completley, insert new seal-
36
ing strip, fit retaining plate, adjust seal-
ing strips and screw down retaining
plate.
Check/replace dust filter
WARNING
Wear a dust mask when working around
the dust filter. Observe safety regulations
on the handling of fine particles.
Note: Wait at least 1 minute before remov-
ing the dust filter so that the dust can settle.
3
6
Figure: KM 125/... with 3 flat fold filters; KM
80-85 mm
105/... has 2 flat fold filters
1 Lid with cleaning device
2 Screw
3 Support
4 Dust filter (flat-fold filter)
 Unscrew the screw.
 Fold the lid up and secure it by means
of the support.
 Take out the dust filter.
 Check dust filter.
 Insert cleaned or new dust filter.
 Place support into retainer.
 Close the lid.
 Screw in the screws and tighten them.
Check suction blower
 Have the suction blower checked for
leaks.
Check by customer service
Checking drive belt of roller brush
 Check the drive belt of the roller brush
for tension, wear and function.
Check by customer service
Replacing fuses
The fuses are located in the MFM box un-
derneath the driver seat.
1 Fuses
 Open the cover of the MFM box.
 Replace defective fuse.
F1 Control CPU
F2 Main fuse
Pole fuse
F70 Charger
Fuses
5 A
175 A
40 A
14
-
EN
Pole fuse
1
3
1 Pole fuse
2 Jumper
3 Nut
Note:A defective pole fuse may only be re-
placed by a Kärcher service technician or
an authorised expert. If this fuse is defec-
tive, check the usage conditions and the
entire control system.
2