Kärcher KM 105/100 R Bp Mode D'emploi page 29

A OFF
Device is switched off
B ON
The appliance is now ready for opera-
tion.
C Drive the machine
Drive to the operating location; in order
to do so, push the accelerator pedal.
Note
Roller brush and side brushes are
raised and switched off.
D Sweeping with sweep roller
Roller brush is lowered.
E Sweeping with roller brush and right
side brush
Roller brush and right side brush are
lowered, the sickle brush (optional) is
ready for operation.
F Sweeping with roller brush and right
and left side brush
Roller brush, right side brush and left
side brush (optional) are lowered, the
sickle brush (optional) is activated.
Safety Devices
WARNING
This appliance is equipped with a variety of
safety installations. The proper function of
every safety installation must be checked
prior to operation and must NOT be over-
ridden!
Main switch
The main switch serves the immediate
shutdown of the electrical drives in case of
emergencies and may only be used for this
purpose.
Cover on the left
The left cover is equipped with a safety in-
stallation that switches off the running de-
vice when it is opened and issues a warn-
ing message on the display.
Waste container (low emptying system)
Both waste containers are equipped with a
safety installation that switches off the run-
ning device when it is opened and issues a
warning message on the display.
Waste container (high emptying system)
The high emptying system is equipped with
a safety installation that blocks the sweep-
ing operation during the emptying proce-
dure.
Button for two-hand operation
Appliances with a high emptying system
are equipped with a button for two-hand op-
eration.
 For emptying the waste container, the
button must be pressed together with
the keys of the high emptying system.
Safety support waste container (high
emptying system)
The safety support is attached to the cross-
beam by means of 2 star screws for stor-
age.
CAUTION
Risk of injury!
 During any work underneath the lifted
waste container, the lifting cylinder
must be secured by means of a safety
support.
 Perform the safeguarding only from
outside the hazard zone.
 Remove safety support, in order to do
this, unscrew 2 star screws.
 Insert safety support into the piston rod
for the lifting cylinder and secure it.
Note: The round notch must point up-
wards.
Parking brake
The appliance is equipped with an auto-
matic parking brake that is integrated in the
front-wheel drive.
The parking brake takes effect as soon as
the device comes to a standstill and the ac-
celerator pedal is released.
Before Startup
Remove the appliance cover
 The cover with the seat can be removed
for repair or maintenance work.
 Prior to removing the cover, disconnet
the electrical socket plug connection of
the seat contact switch.
Opening/closing cover on the left
ATTENTION
The left cover may only be opened when
the programme selector switch is in the
"OFF" position and the key (Intelligent Key)
is removed.
Opening the left cover during operation of
the device is prohibited.
 Grab the front of the cover on the re-
cessed grip, unlock it towards the top
and swivel it to the side.
7
-
EN
Illustration is symbolic, here KM 105/...
Note: The cover is equipped with a safety
installation that switches off the drive when
it is opened and issues a warning message
on the display. If the cover is not properly
closed the device will not operate.
If a warning message is pending, it can be
reset as follows:
 Completely close the bonnet (locking in
place).
 Turn the programme selector switch to
"ON".
 Sit on the driver seat.
Unloading tips
DANGER
Risk of personal injury or damage!
 Observe the weight of the appliance
when you load it!
 Do not use a forklift truck to unload the
machine as this may damage it.
ATTENTION
Charge the battery before commissioning
the machine.
Net weight (transport weight)
Weight (without driver, without attachment
kits, without batteries)
KM 105/100 R (low emptying sys-
tem)
KM 105/110 R (high emptying
system)
KM 125/130 R (high emptying
system)
Weight (without driver, without attachment
kits, with batteries)
KM 105/100 R (low emptying sys-
tem)
KM 105/110 R (high emptying
system)
KM 125/130 R (high emptying
system)
* If upgrade kits are installed, the weight is
respectively higher.
 When loading the appliance a suitable
ramp must be used!
 If the machine is delivered on a pallet,
you must create an unloading ramp us-
ing the boards provided.
To unload the machine, proceed as follows:
 Cut plastic packing belt and remove foil.
 Remove the elastic tape fasteners at
the stop points.
 Connect battery (see section on Care
and maintenance)
 Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
 Place the boards on the edge of the pal-
let. Place the boards in such a way that
305 kg
405 kg
500 kg
490 kg
590 kg
820 kg
29