GRAUPNER heim UNI-Mechanik 2000 Mode D'emploi page 52

Additional items required: (parts not included in basic mechanics kit)
Recommended motors and accessories for UNI-Mechanics 2000
Motor Capacity
cc
OS MAX 61 9,95
RX-HGL »C«
OS MAX 61 9,97
SX- HGL »C«
OS MAX 91 14,95
FX / SX- HGL
Clutch / ring gear combinations, according to motor and rotor diameter
Motor
(examples)
OS MAX 61 RX/SX-HGL »C«
Order No. 1890, 1892 ...
OS MAX 91 FX / SX- HGL
Order No. 1922, 1935
OS MAX 91 FX / SX- HGL
Order No. 1922, 1935
OS MAX 91 FX (modified)
Order No. 1816
Main rotor blades, (suitability varies according to fuselage kit used)
Order No. 1246B
Order No. 1266
Order No. 1272
Glowplug battery, e.g.
2 V glowplug battery, Order No.3694 or 771 (use only with dropping resistor, No.1685 or 1694.)
Fuel: AeroSynth COMPETITION SX-10, Order No. 2811
Starter: Electric starter, Order No. 1628 or 1626 (12 V starter battery, Order No. 2593).
Radio control equipment (see main Graupner catalogue)
We recommend that you use a radio control system equipped with specialist helicopter options
or a micro-computer RC system such as the mc-12, mc-14, mc-15, mc-19, mc-22 or mc-24.
The minimum requirement for the RC system is that it has a 3-point swashplate mixer and five
servos for the functions pitch-axis, roll, collective pitch, tail rotor and throttle.
RC functions
Swashplate, lateral:
Swashplate, longitudinal:
Tail rotor:
Throttle and collective pitch:
Also recommended:
Servos (we recommend high-performance servos only) such as: C 4421, Order No. 3892
Gyro:
Gyro-System PIEZO 5000, Order No. 5146 with Super-Servo NES-8700G, Order No. 5156 or
Gyro-System PIEZO 550, Order No. 5147 or Gyro-System G490T, Order No. 5137
Electronic rotor speed governor: mc-HELI-CONTROL, Order No. 3286
Receiver battery: for safety reasons we recommend that you use a battery of at least 1800
mAh capacity: POWER switch harness, Order No. 3050, with 4RC-3000 MH battery, Order
No. 2568. We also advise the use of the NC-AKKU-CONTROLER, Order No. 3155, so that you
can monitor the condition of the receiver battery at all times.
Order Exhaust
No. manifold
1892 2239A
-
1890 2238A
1922, 2238A
1935
Rotor-Ø Ratio Clutch bell
approx.
150 cm 9:1 4448.124
150 cm 7,7:1 4448.126A
180 cm 10:1 4448.122
150cm 7,7:1 4448.126
GFRP, reflex
CFRP, symmetrical
CFRP, reflex
Roll function, right/left
Pitch-axis function, forward/back
Rotation around the vertical (yaw) axis
Climb and descent
Gyro stabilisation of the tail rotor function
Electronic regulation of main rotor speed
UNI-Mechanics 2000
Silencer Tuned pipe
silencer
- 2240 or 2250
2253 -
2258 2240 or 2250
2258 2240 or 2250
Clutch shoe Taper collet
4448.79
4448.79A
4448.79A
4448.79A
688 mm long Rotor Ø 1551 mm
686 mm long Rotor Ø 1547 mm
825 mm Rotor Ø 1825 mm
6
Ring gear
4448.77 4448.107A
4448.77 4448.107C
4448.77 4448.107A
4448.77A 4448.107C