Table des Matières
Publicité
Certains de ces blocs fonctionnels sont peut-être déjà utilisés dans les macros.
Compensation
–
COMPENSATIONS [817] – 0.00 %
–
INERTIA COMP [818] – 0.00 %
–
SCALED RATE [819] – 0.00 %
–
LINE SPEED RATE [820] – 0.00 %
10.00 % – [805] DIAMETER
–
10.00 % – [806] MINIMUM DIAMETER –
0.00 % – [807] VARIABLE INERTIA
–
0.00 % – [808] FIXED INERTIA
–
0.00 % – [809] WIDTH
–
FALSE – [810] UNWIND
–
0.00 % – [811] LINE SPD DEMAND
–
0.00 % – [812] RATE CAL
–
FALSE – [813] REVERSE
–
0.00 % – [814] DYNAMIC COMP
–
0.00 % – [815] STATIC COMP
–
0.00 % – [816] MOD REEL SPEED
–
690+ Series Frequency Inverter
Diameter Calc
–
CURRENT CORE [834] – 10.00 %
–
DIAMETER [835] – 10.00 %
–
MOD LINE SPEED [836] – 0.00 %
FALSE – [774] UNWIND
– MOD WINDER SPEED [837] – 0.00 %
FALSE – [775] OVER-WIND
FALSE – [821] DIAMETER HOLD
–
FALSE – [776] OVER SPD ENABLE
FALSE – [822] PRESET ENABLE
–
5.00 % – [777] UTS THRESHOLD
FALSE – [823] SELECT CORE 2
–
0.00 % – [778] LINE SPEED
FALSE – [824] SEL EXT DIAMETER –
0.00 % – [779] MOD REEL SPEED
FALSE – [825] TENSION ENABLE
–
10.00 % – [780] DIAMETER
10.00 % – [826] CORE 1
–
10.00 % – [781] MINIMUM DIAMETER
10.00 % – [827] CORE 2
–
0.00 % – [782] OVER SPEED
5.00 s – [828] DIAMETER TC
–
0.00 % – [783] SPEED TRIM
0.00 % – [829] EXT DIAMETER
–
0.00 % – [830] LINE SPEED
–
10.00 % – [831] MINIMUM DIAMETER –
5.00 % – [832] MINIMUM SPEED
–
0.00 % – [833] REEL SPEED
–
Winder
Speed Calc
–
SPEED DEMAND
[784] – 0.00 %
–
UP TO SPD (UTS)
[785] – TRUE
–
FALSE – [838] HYPERBOLIC TAPER –
–
FALSE – [839] STALL ENABLE
–
FALSE – [840] BOOST ENABLE
–
FALSE – [841] FIXED BOOST
–
FALSE – [842] FIXED STALL TEN
–
0.00 % – [843] CURRENT CORE
–
10.00 % – [844] DIAMETER
–
0.00 % – [845] BOOST
–
1.000 s – [846] TENSION RAMP
–
0.00 % – [847] STALL TENSION
0.00 % – [848] TAPER SPT
0.00 % – [849] TENSION SPT
Taper Calc
–
TAPERED DEMAND [850] – 0.00 %
–
–
TENSION DEMAND [851] – 0.00 %
–
FALSE – [786] OVER-WIND
–
FALSE – [787] TENSION ENABLE
–
0.00 % – [788] TENSION DEMAND
–
200.00 % – [789] TORQUE LIMIT
–
–
–
–
–
–
–
–
11-18
Les Macros
Blocs fonctionnels
Torque Calc
POS TORQUE LIMIT [790] – 200.00 %
NEG TORQUE LIMIT [791] – -200.00 %
–
–
–
–
Publicité
Table des Matières
