Parker 690 Série Manuel D'installation page 155

Analog Input 1
– VALUE [ 16] – 0.00 %
– BREAK [ 18] – FALSE
100.00 % – [ 14] SCALE –
0.00 % – [ 15] OFFSET –
-10 .. 10 V – [ 13] TYPE –
FALSE – [ 12] BREAK ENABLE –
0.00 % – [ 17] BREAK VALUE –
Analog Input 2
– VALUE [ 25] – 0.00 %
– BREAK [ 27] – FALSE
100.00 % – [ 23] SCALE –
0.00 % – [ 24] OFFSET –
-10 .. 10 V – [ 22] TYPE –
FALSE – [ 21] BREAK ENABLE –
0.00 % – [ 26] BREAK VALUE –
Analog Input 3
– VALUE [715] – 0.00 %
– BREAK [717] – FALSE
100.00 % – [713] SCALE –
0.00 % – [714] OFFSET –
-10 .. 10 V – [712] TYPE –
FALSE – [711] BREAK ENABLE –
0.00 % – [716] BREAK VALUE –
Digital Input 1
VALUE [ 31] – FALSE (5)
FALSE – [ 30] INVERT –
Digital Input 2
(6)
VALUE [ 34] – FALSE
FALSE – [ 33] INVERT –
Digital Input 3
(7)
VALUE [ 37] – FALSE
FALSE – [ 36] INVERT –
Digital Input 4
VALUE [ 40] – FALSE (19)
FALSE – [ 39] INVERT –
Digital Input 5
VALUE [ 43] – FALSE (9)
FALSE – [ 42] INVERT –
Digital Input 6
(8)
VALUE [726] – FALSE
FALSE – [725] INVERT –
Digital Input 7
VALUE [728] – FALSE (10)
FALSE – [727] INVERT –
Digital Input 8 = COAST STOP
690+ Series Frequency Inverter
Value Func 1
(11)
OUTPUT [133] – 0.00 %
(3) 0.00 % – [130] INPUT A –
(2)
0.00 % – [131] INPUT B –
0.00 – [132] INPUT C –
A+B+C – [134] TYPE –
I/O Trips
– THERMIST [1155] – FALSE
– ENCODER TB [1156] – FALSE
– EXTERNAL [234] – FALSE
FALSE – [760] INVERT THERMIST –
FALSE – [1154] INVERT ENC TRIP –
COAST – [233] EXT TRIP MODE –
(1) FALSE – [235] INPUT 1 BREAK –
(4)
FALSE – [236] INPUT 2 BREAK –
Trips Status
ACTIVE TRIPS [ 4] – 0000
ACTIVE TRIPS+ [740] – 0000
WARNINGS [ 5] – 0000
WARNINGS+ [741] – 0000
FIRST TRIP [ 6] – NONE
0600 – [231] DISABLED TRIPS –
0040 – [742] DISABLED TRIPS+ –
Sequencing Logic
– TRIPPED [289] – FALSE
– RUNNING [285] – FALSE
– JOGGING [302] – FALSE
– STOPPING [303] – FALSE
– OUTPUT CONTACTOR [286] – FALSE
– SWITCH ON ENABLE [288] – FALSE
– SWITCHED ON [306] – FALSE
– READY [287] – FALSE
– SYSTEM RESET [305] – FALSE
– SEQUENCER STATE [301] – START ENABLED
– REMOTE REV OUT [296] – FALSE
– HEALTHY [274] – TRUE
FALSE – [291] RUN FORWARD –
FALSE – [292] RUN REVERSE –
FALSE – [293] NOT STOP –
FALSE – [280] JOG –
TRUE – [1235] CONTACTOR CLOSED –
TRUE – [276] DRIVE ENABLE –
TRUE – [277] NOT FAST STOP –
TRUE – [278] NOT COAST STOP –
FALSE – [294] REMOTE REVERSE –
FALSE – [282] REM TRIP RESET –
TRUE – [290] TRIP RST BY RUN –
FALSE – [283] POWER UP START –
Reference
SPEED DEMAND [255] – 0.00 %
SPEED SETPOINT [254] – 0.00 %
REVERSE [256] – FALSE
LOCAL SETPOINT [247] – 0.00 %
LOCAL REVERSE [250] – FALSE
COMMS SETPOINT [770] – 0.00 %
(12)
0.00 % – [245] REMOTE SETPOINT –
0.00 % – [248] SPEED TRIM –
110.00 % – [252] MAX SPEED CLAMP –
-110.00 % – [253] MIN SPEED CLAMP –
FALSE – [243] TRIM IN LOCAL –
SENSORLESS VEC – [1157]
(16)
FALSE – [249] REMOTE REVERSE –
** 5.50 kW – [1158]
** 50.0 Hz – [1159]
Reference Ramp ** 400.0 V – [1160]
– RAMPING [698] – FALSE
** 11.30 A – [ 64]
LINEAR – [244] RAMP TYPE –
** 3.39 A – [ 65]
10.0 s – [258] ACCEL TIME –
** 1445.0 rpm – [ 83]
10.0 s – [259] DECEL TIME –
** STAR – [124]
FALSE – [268] SYMMETRIC MODE –
** 4 – [ 84]
10.0 s – [267] SYMMETRIC TIME –
10.00 /s^2 – [692] SRAMP ACCEL –
** 0.90 – [242]
10.00 /s^2 – [693] SRAMP DECEL –
** 2.0 – [1164]
10.00 /s^3 – [694] SRAMP JERK 1 –
** 1.3625 Ohm – [119]
10.00 /s^3 – [695] SRAMP JERK 2 –
** 43.37 mH – [120]
10.00 /s^3 – [696] SRAMP JERK 3 –
** 173.48 mH – [121]
10.00 /s^3 – [697] SRAMP JERK 4 –
TRUE – [691] SRAMP CONTINUOUS –
276.04 ms – [1163]
FALSE – [260] HOLD –
Reference Stop
RAMPED – [279] RUN STOP MODE –
10.0 s – [263] STOP TIME –
0.10 % – [266] STOP ZERO SPEED –
0.500 s – [284] STOP DELAY –
RAMPED – [304] FAST STOP MODE –
30.0 s – [275] FAST STOP LIMIT –
0.1 s – [264] FAST STOP TIME –
1200 Hz/s – [126] FINAL STOP RATE –
10.0 V – [761] ENCODER SUPPLY
Reference Jog
** 2048 – [566] ENCODER LINES
10.00 % – [246] SETPOINT –
FALSE – [567] ENCODER INVERT
1.0 s – [261] ACCEL TIME –
FALSE –
1.0 s – [262] DECEL TIME –
0.00 % – [359] HYSTERISIS
0.00 % – [357] THRESHOLD
Analog Input 4
– VALUE [722] – 0.00 %
– BREAK [724] – FALSE
100.00 % – [720] SCALE –
0.00 % – [721] OFFSET –
0..+10 V – [719] TYPE –
FALSE – [718] BREAK ENABLE –
0.00 % – [723] BREAK VALUE –
Les Macros
(21)
0.00 % – [ 45] VALUE
100.00 % – [ 46] SCALE
0.00 % – [ 47] OFFSET
TRUE – [ 48] ABSOLUTE
0..+10 V – [ 49] TYPE
–
(18) 0.00 % –
1500 RPM – [1032] MAX SPEED
Motor Data
CONTROL MODE –
POWER –
BASE FREQUENCY –
MOTOR VOLTAGE –
MOTOR CURRENT –
MAG CURRENT –
NAMEPLATE RPM –
MOTOR CONNECTION –
MOTOR POLES –
POWER FACTOR –
OVERLOAD –
STATOR RES –
LEAKAGE INDUC –
MUTUAL INDUC –
ROTOR TIME CONST –
Feedbacks
– DC LINK VOLTS [ 75] – 0 V
0.00 % – [731] VALUE
– TERMINAL VOLTS [1020] – 0 V
100.00 % – [732] SCALE
– SPEED FEEDBACK RPM [569] – 0.00 rpm
0.00 % – [733] OFFSET
– SPEED FEEDBACK HZ [568] – 0.00 Hz
FALSE – [734] ABSOLUTE
– SPEED FEEDBACK % [749] – 0.00 % (17)
-10 .. +10 V – [735] TYPE
– ENCODER FBK % [1238] – 0.00 %
– ENCODER COUNT [1016] – 0
– TORQUE FEEDBACK [ 70] – 0.00 % (20)
– FIELD FEEDBACK [ 73] – 0.00 %
0.00 % – [800] VALUE
– MOTOR CURRENT % [ 66] – 0.00 %
100.00 % – [801] SCALE
– MOTOR CURRENT [ 67] – 0.0 A
0.00 % – [802] OFFSET
–
FALSE – [803] ABSOLUTE
–
-10 .. +10 V – [804] TYPE
–
[ 50] QUADRATIC TORQUE –
(13) FALSE – [ 52]
TRUE – [ 51]
Zero Speed
– AT ZERO SPD FBK [1233] – TRUE
– AT ZERO SPD DMD [360] – TRUE
– AT STANDSTILL [1234] – TRUE
–
(15) FALSE – [ 55]
–
FALSE – [ 54]
(14)
FALSE – [737] VALUE
FALSE – [736] INVERT
Macro 6: Variateur "Système"
11-14
Analog Output 1
–
–
–
–
–
Setpoint Scale
OUTPUT [ 59] – 0.0 Hz
[ 58] INPUT –
–
Analog Output 2
–
–
–
–
–
Analog Output 3
–
–
–
–
–
Digital Output 1
VALUE –
INVERT –
Digital Output 2
VALUE –
INVERT –
Digital Output 3
–
–