Parker 690 Série Manuel D'installation page 150

Analog Input 1
(1) Line Speed ANIN1 (next sheet)
– VALUE [ 16] – 0.00 %
– BREAK [ 18] – FALSE
100.00 % – [ 14] SCALE –
0.00 % – [ 15] OFFSET –
-10..+10 V – [ 13] TYPE –
FALSE – [ 12] BREAK ENABLE –
0.00 % – [ 17] BREAK VALUE –
Analog Input 2
(3) Feedback ANIN2 (next sheet)
– VALUE [ 25] – 0.00 %
– BREAK [ 27] – FALSE
100.00 % – [ 23] SCALE –
0.00 % – [ 24] OFFSET –
-10..+10 V – [ 22] TYPE –
FALSE – [ 21] BREAK ENABLE –
0.00 % – [ 26] BREAK VALUE –
Digital Input 1
VALUE [ 31] – FALSE
FALSE – [ 30] INVERT –
Digital Input 2
VALUE [ 34] – FALSE
FALSE – [ 33] INVERT –
Digital Input 3
VALUE [ 37] – FALSE
FALSE – [ 36] INVERT –
Digital Input 4
VALUE [ 40] – FALSE
FALSE – [ 39] INVERT –
Digital Input 5
VALUE [ 43] – FALSE
FALSE – [ 42] INVERT –
Digital Input 6
VALUE [726] – FALSE
FALSE – [725] INVERT –
Digital Input 7
VALUE [728] – FALSE
FALSE – [727] INVERT –
690+ Series Frequency Inverter
I/O Trips
– THERMIST [1155] – FALSE
– ENCODER TB [1156] – FALSE
– EXTERNAL [234] – FALSE
FALSE – [760] INVERT THERMIST –
FALSE – [1154] INVERT ENC TRIP –
(2) FALSE – [235] INPUT 1 BREAK –
(4) FALSE – [236] INPUT 2 BREAK –
Trips Status
ACTIVE TRIPS [ 4] – 0000
ACTIVE TRIPS+ [740] – 0000
WARNINGS [ 5] – 0000
WARNINGS+ [741] – 0000
FIRST TRIP [ 6] – NONE
0000 – [231] DISABLED TRIPS –
0040 – [742] DISABLED TRIPS+ –
(5) Run DIN1 (next sheet)
Sequencing Logic
– TRIPPED [289] – FALSE
– RUNNING [285] – FALSE
– JOGGING [302] – FALSE
– STOPPING [303] – FALSE
– OUTPUT CONTACTOR [286] – FALSE
– SWITCH ON ENABLE [288] – FALSE
– SWITCHED ON [306] – FALSE
– READY [287] – FALSE
– SYSTEM RESET [305] – FALSE
– SEQUENCER STATE [301] – START ENABLED
– REMOTE REV OUT [296] – FALSE
– HEALTHY [274] – TRUE
(6)
FALSE – [291] RUN FORWARD –
(7)
FALSE – [292] RUN REVERSE –
(35) FALSE – [293] NOT STOP –
(37) FALSE – [280] JOG –
TRUE – [1235] CONTACTOR CLOSED –
TRUE – [276] DRIVE ENABLE –
TRUE – [277] NOT FAST STOP –
TRUE – [278] NOT COAST STOP –
(36) FALSE – [294] REMOTE REVERSE –
(8)
FALSE – [282] REM TRIP RESET –
TRUE – [290] TRIP RST BY RUN –
FALSE – [283] POWER UP START –
Analog Input 3
(15)
– VALUE [715] – 0.00 %
– BREAK [717] – FALSE
100.00 % – [713] SCALE –
0.00 % – [714] OFFSET –
0..+10 V – [712] TYPE –
FALSE – [711] BREAK ENABLE –
0.00 % – [716] BREAK VALUE –
Speed Demand (next sheet) (14) 0.00 %
0.00 % – [248] SPEED TRIM
100.00 % – [252] MAX SPEED CLAMP
-100.00 % – [253] MIN SPEED CLAMP
FALSE – [243] TRIM IN LOCAL
(13)
FALSE
LINEAR
10.0 s
10.0 s
FALSE
10.0 s
10.00 /s^2
10.00 /s^2
10.00 /s^3
10.00 /s^3
10.00 /s^3
10.00 /s^3
FALSE
FALSE
RAMPED
10.0 s – [263] STOP TIME
0.10 % – [266] STOP ZERO SPEED
0.500 s – [284] STOP DELAY
RAMPED
(11)
Ready (next sheet)
30.0 s – [275] FAST STOP LIMIT
0.1 s – [264] FAST STOP TIME
1200 Hz/s – [126] FINAL STOP RATE
10.00 % – [246] SETPOINT
1.0 s – [261] ACCEL TIME
1.0 s – [262] DECEL TIME
Tension/Dancer Spt ANOUT3 (next sheet)
Analog Input 4
Tension Spt ANIN3 (next sheet)
– VALUE
– BREAK
100.00 % – [720] SCALE
0.00 % – [721] OFFSET
0..+10 V – [719] TYPE
FALSE – [718] BREAK ENABLE
0.00 % – [723] BREAK VALUE
Reference
SPEED DEMAND [255] – 0.00 % (17)
SPEED SETPOINT [254] – 0.00 %
REVERSE [256] – FALSE
LOCAL SETPOINT [247] – 0.00 %
LOCAL REVERSE [250] – FALSE
COMMS SETPOINT [269] – 0.00 %
– [245] REMOTE SETPOINT –
–
(18)
–
–
–
– [249] REMOTE REVERSE –
Reference Ramp
– RAMPING [698] – FALSE
– [244] RAMP TYPE –
– [258] ACCEL TIME –
– [259] DECEL TIME –
– [268] SYMMETRIC MODE –
– [267] SYMMETRIC TIME –
– [692] SRAMP ACCEL –
– [693] SRAMP DECEL –
– [694] SRAMP JERK 1 –
– [695] SRAMP JERK 2 –
– [696] SRAMP JERK 3 –
– [697] SRAMP JERK 4 –
– [691] SRAMP CONTINUOUS –
– [260] HOLD –
Reference Stop
(19)
– [279] RUN STOP MODE –
–
–
–
– [304] FAST STOP MODE –
–
–
(20)
–
Reference Jog
-10 .. +10 V
–
–
–
Diameter ANOUT2 (next sheet)
(9)
(16)
Taper Spt ANIN4 (next sheet)
[722] – 0.00 % (10)
[724] – FALSE
–
–
–
(12)
–
–
Macro 4: Enrouleur piloté en vitesse (SPW)
11-9
Les Macros
Analog Output 1
0.00 % – [ 45] VALUE –
100.00 % – [ 46] SCALE –
0.00 % – [ 47] OFFSET –
FALSE – [ 48] ABSOLUTE –
0..+10 V – [ 49] TYPE –
Setpoint Scale
– OUTPUT [ 59] – 0.0 Hz
0.00 % – [ 58] INPUT –
1500 RPM – [1032] MAX SPEED –
Analog Output 2
0.00 % – [731] VALUE –
100.00 % – [732] SCALE –
0.00 % – [733] OFFSET –
FALSE – [734] ABSOLUTE –
0 .. +10 V – [735] TYPE –
Analog Output 3
0.00 % – [800] VALUE –
100.00 % – [801] SCALE –
0.00 % – [802] OFFSET –
FALSE – [803] ABSOLUTE –
– [804] TYPE –
Digital Output 1
FALSE – [ 52] VALUE –
TRUE – [ 51] INVERT –
Digital Output 2
FALSE – [ 55] VALUE –
FALSE – [ 54] INVERT –
Digital Output 3
FALSE – [737] VALUE –
FALSE – [736] INVERT –