Atlas Copco QAS plus 160 Fd S5 Manuel D'instructions page 171

0-1.D5
0-1.D5
0-1.D5
0-1.D5
0-1.D5
PE N L1 L2
PE N L1 L2 L3 PE N L1 L2
(canopy) (canopy)
O11 - Power Locks - 1x5P O14 - Power Locks - 2x5P
Table 9 - Wire marking
Socket L1 L2 L3 N
X2 2L1 2L2 2L3 2N
X3 3L1 3L2 3L3 3N
X4 4L1 4L2 4L3 4N
X5 5L1 5L2 5L3 5N
X6 6L1 6L2 6L3 6N
X7 7L1 7L2 7L3 7N
X8 8L1 8L2 8L3 8N
X9 9L1 9L2 9L3 9N
X10 10L1 10L2 10L3 10N
X11 11L1 11L2 11L3 11N
Table 10 - 1PH socket connection
Socket slot Socket 1 Phase Socket 2
Socket slot 1 X2 L1 X3
Socket slot 2 X4 L3 X5
Socket slot 3 X6 L2 X7
Socket slot 4 X8 L1 X9
Socket slot 5 X10 L3 X11
Configuration set 1
Socket type
Socket slot 1 2x16 1PH or 2x16 3PH or 2x32 3PH
Socket slot 2 2x16 1PH or 2x16 3PH or 2x32 3PH
Socket slot 3 2x16 1PH or 2x16 3PH or 2x32 3PH
Socket slot 4 2x16 1PH or 2x16 3PH or 2x32 3PH
Socket slot 5 2x16 1PH or 2x16 3PH or 2x32 3PH
O12 - Sockets
L3
L2
L1
N
PE
O2 - Dual
frequency
C2
U > U >
C1
L3
L3
425
L1 L2
L3
PE
N
NOTES
Table 11 - Cross-section/colour
Note 4: This representation of the sockets option is only one example of connection. Several configurations can be made.
Note 5: See Table 9 for wire marking.
Phase Socket L1-L2-L3 N PE
Note 6: See Table 11 for wire cross-section and colour.
L2 16A 1PH c0 c6 c54
Note 7: Connect 1PH sockets alternating the connection line as shown Table 10.
L1 16A 3PH c0 c6 c54
Note 8: Two types of circuit breakers migth be selected: magnet-thermal circuit breaker or earth leakage (ELCB) circuit breaker. With 1PH sockets only ELCB can be mounted.
L3 32A 3PH e0 e6 e54
Note 9: In each socket slot migth be fitted 2 sockets with exception of 63A and 125A sockets, in this case only one socket per slot is allowed. 63A and 125 sockets can only be
L2 63A 3PH gx0 gx6 gx54
gx54
L1 125A 3PH hx0 hx6
Configuration set 2
Socket Circuit braker
Socket type
Label label
X2, X3 Q2, Q3 2x16 1PH or 2x16 3PH or 2x32 3PH
X4, X5 Q4, Q5
2x16 1PH or 2x16 3PH or 2x32 3PH
X6, X7 Q6, Q7 2x16 1PH or 2x16 3PH or 2x32 3PH
X8, X9 Q8, Q9 2x16 1PH or 2x16 3PH or 2x32 3PH
X10, X11 Q10, Q11 1x63 3PH or 1x125 3PH
C2
C2
U >
C1
C1
T
425 425
L1 L2
L3
PE
N
With 63A and 125A sockets, an earth leakage add-on blockis used when ELCB type is selected.
mounted in slots 3, 4 or 5. There are 4 configuration sets depending on number of the 63A/125A sockets selected: No 63A/125A sockets, 1 unit 63A/125A
socket, 2 units 63A/125A sockets, 1 unit 63A socket and 2 units 63A/125A sockets. Table 12 shows the 4 configurations sets with the corresponding markings of
sockets and circuit breakers.
Table 12 - Socket configuration set
Configuration set 3
Socket Circuit braker
Socket type
Label label
X2, X3 Q2, Q3 2x16 1PH or 2x16 3PH or 2x32 3PH
X4, X5 Q4, Q5
2x16 1PH or 2x16 3PH or 2x32 3PH
X6, X7 Q6, Q7 2x16 1PH or 2x16 3PH or 2x32 3PH
X8, X9 Q8, Q9 1x63 3PH or 1x125 3PH
X11 Q11 1x63 3PH or 1x125 3PH
- 171 -
C2
U >
I>> I>>
I I
C1
16 A 16 A
30 mA 30 mA
425
N L1 N L1
PE PE
Configuration set 4
Socket Circuit braker Socket
Socket type
Label label Label
X2, X3 Q2, Q3 2x16 1PH or 2x16 3PH or 2x32 3PH X2, X3
X4, X5 Q4, Q5 X4, X5
2x16 1PH or 2x16 3PH or 2x32 3PH
X6, X7 Q6, Q7 1x63 3PH X9
X10 Q10 1x63 3PH or 1x125 3PH X10
X11 Q11 1x63 3PH or 1x125 3PH X11
C2
U >
I>>
I
C1
16 A
30 mA
N L1
PE
Circuit braker
label
Q2, Q3
Q4, Q5
Q9
Q10
Q11