Bronpi LONDRES Instructions D'installation, D'utilisation Et D'entretien page 52

Due to safety reasons, the door must remain closed when the fireplaces is being used. You should only open the door for loading the
fuel.
In order to refill the fuel, open the door slowly, open the primary air intake, introduce the wood and close the door. After 3-5 minutes, return to
the combustion recommended regulation.
Do not overload the equipment (see maximum fuel load). Too much fuel and too much air for the combustion can cause the
overheating and, therefore, damage the equipment. The non-compliance of this rule shall invalidate the warranty.
9. SERVICING AND CARE
The insert, the chimney and, in general, the whole installation, must be cleaned completely at least once a year or when necessary.
WARNING!! Maintenance and servicing operations must be done when the insert is cold.
9.1 CLEANING THE CHIMNEY
When the wood is burnt slowly, it produces tars and other organic vapours that combined with the humidity they create the creosote (soot).
An excessive accumulation of soot may cause problems in the smoke outlet and even the smoke duct may suffer a fire. A chimney sweep
should perform this task and, at the same time, examine the smoke duct. During the cleaning tasks, it is necessary to remove the ash pan,
the grille and the smoke baffle plate in order to makes easier the fall of the soot.
It is recommended to use anti-soot envelopes during the operation of the insert at least once a week. These envelopes are placed directly on
the fire and you can buy them in the same Bronpi distributor where you bought your fireplace.
9.2 CLEANING THE GLASS
IMPORTANT:
Clean the glass only when it is cold in order to avoid its explosion.
You can use specific products such as vitro ceramic-cleaning products. Do not use aggressive or abrasive products that stain the
glass.
You can find Bronpi vitro ceramic-cleaning product in the same Bronpi distributor where you bought your fireplace.
BREAKAGE OF GLASSES: the glasses, as they are vitro ceramic, resist until 750ºC and they are not subject to thermal shocks. The
breakage can only be caused by mechanical shocks (crashes or violent closing of the door, etc). Therefore, its replacement is not
included in the warranty.
9.3 CLEANING THE ASH
All inserts have an ash pan for the ash collection. We recommend emptying the ash pan regularly in order to avoid that it is full completely so
that the grille does not overheat. Moreover, we recommend leaving 2-3 cm of ash on the base.
9.4 SPECIFICATIONS FOR MODELS WITH OVEN
(Only models Everest and Everest Visión)
Over time and with the use, this model can create soot deposits in the
external parts of the oven. These deposits can obstruct the draw and
cause a malfunction of the insert. For this reason, it is important to remove
them through a register that is hidden under the logo of the oven door. It is
necessary to unscrew the logo and use the hole in order to proceed with the
cleaning (see drawing D9.1).
When you are cleaning the oven, please be careful and do not
use aggressive products because they can wear down the paint and too much water can oxidise it.
In the model Everest Visión the cleaning register is hidden under
the door. To cleaning it, the cover must be unscrewed and the register will
appear (see drawing D9.2).
9.5 EXTERNAL CLEANING
Do not clean the external surface of the insert with water or abrasive products because they may damage the fireplace. Use a feather duster
or a rag a bit wet.
10. SEASONAL STOPPAGES
After cleaning the chimney and the insert by removing the ash and other residues, close all doors and regulators.
It is recommended to clean the chimney at least once a year. Meanwhile, check the joints because if they are not in good condition (they do
not adjust to the door), they do not guarantee the proper operation of the insert! For this reason, it would be necessary to change them. You
can find this spare part in the same Bronpi distributor where you bought your insert.
If there is humidity in the place where the fireplace is installed, put absorbent salts inside the equipment. Protect the internal parts with neutral
vaseline in order to keep the appearance along the time.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS 51
D9.1
D9.2
INSERTS