Bronpi LONDRES Instructions D'installation, D'utilisation Et D'entretien page 47

PLACEMENT OF DOORS IN CAIRO-D
The Cairo-D model has two doors. If you need to remove these doors to facilitate the installation process of the insert, remember to place the
doors later in the correct position, to ensure the correct operation of the equipment. These doors are not interchangeable. It should be noted
that the door that is placed on the side with the air regulations as well as the ash drawer has a ceramic cord in the bottom to generate the
sealing with the ash drawer
(see drawing D2.64).
The door on the other side of
the insert only has a ceramic
cord to ensure the sealing of
the combustion chamber
(see drawing D2.65).
DOOR CLOSING ADJUSTMENT
It is advisable to check the effective state of the door seals because if they are not
perfectly intact (i.e. they no longer fit with the front and/or door), they do not ensure
the correct functioning of the chimney! In the Cairo and Cairo-D models, you can
adjust the adjustment of the door according to the progressive wear of the joints
through the screws found in the front, tightening and loosening these screws will get
the correct adjustment of the door. (See drawings D2.66).
PLACEMENT/REPLACEMENT FRAME
All inserts in this series have a standard 3-sided frame (for Cairo-70 model) or 4
(for Cairo-90 and Cairo-110 models). The standard frame is removable for easy
installation. To dismantle the standard frame, proceed as follows (see drawing
D2.67):
1. Remove the door by opening it and pulling it upwards.
2. Unscrew the frame screws indicated in the drawing, two on each side of
the frame.
D2.66
3. Remove the frame and place the insert, fix and reassemble the frame and the door.
PLACING HEIGHT ADJUSTABLE FEET
The models of the Cairo-90 and Cairo-110
are screwed onto the wooden pallet for easy
transport (see drawing D2.68). Inside the
combustion chamber you will find the two legs
of the insert, which are adjustable in height
according to your need. The positioning of the
same is very simple; you only have to screw
these legs with the 8 screws that are supplied
to the structure of the appliance, choosing
previously the desired height. (See drawing
D2.69)
DISTANCE BETWEEN THE INSERT AND THE CLADDING WALLS
In the Cairo-70 model, there are ventilation slots both on the sides and at the rear (see drawing
D2.70). These slots are important to guarantee the air flow of the blower, as well as for the ventilation
of the insert itself. The installer must respect a minimum safety distance between the cladding
walls and the side and rear walls of at least 8/10 cm, as well as not covering the slots of the insert,
otherwise the blower flow rate would be reduced and there is a possibility of overheating in the body
of the insert, which could cause structural damage to the device itself, which would not be covered
by the warranty that Bronpi Calefacción offers for its products.
3. INSTALLATION AND SAFETY INSTRUCTIONS
The way of installing the insert will affect the safety and the proper operation. For this reason, it is
recommendable that the installation is carried out by people who are qualified and informed about the compliance with the installation and
safety norms. If an insert is not properly installed it may cause serious damage.
Before the installation, follow the next verifications:
• Make sure that the floor can sustain the weight of the equipment and make a proper isolation in the case that it is made of flammable
material (wood) or a material that can be affected by a thermal shock (plaster cast, for example). If the equipment is installed on a
floor which is not completely refractory or inflammable such as parquet, carpet, etc, it is necessary to replace this part or introduce a
fire-resistant base so that it protrudes out the fireplace 30 cm. Example of materials include steel flooring, glass base or any other type
of fire-resistant material.
• Make sure that there is proper ventilation in the place where it is installed (air intake) (see section 5 of the manual).
• Avoid the installation in places where there are collective ventilation pipes, hoods with or without extractor, B type gas equipments,
heat pumps or equipments that can cause that the draw of the chimney is not good if they are used at the same time.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
D2.64
D2.68
46
D2.67
D2.70
D2.65
D2.69
INSERTS