The Model Templates In Detail - Multiplex ROYALevo 7 Manuel D'utilisation

ROYAL evo 7
!
Caution
Ensure that the throttle limiter is at Idle before you acti-
vate Direct Throttle (switch "DTC" (N) to position "1"),
otherwise the motor will immediately run at full-
throttle!
Helicopter throttle
Throttle
+100%
Throttle curve
P2
+50%
P1
Trim
range
(20%)
0%
Note: cutting the motor
Cutting the (glow-) motor is carried out using the "THR-
CUT" (H) button - not with the throttle trim. The throttle
servo is held at the OFF position for as long as you hold
the button pressed in.
Step
Test-flying
Your newly set-up model should now be ready to fly.
Carry out a thorough check of all the working systems
before you attempt to fly it for the first time.
Fine adjustments, especially to the mixers and transmit-
ter control settings, can only be made during the test-
flying programme with the new model. Don't make
changes in a menu during a flight. It is always better to
use the safe, convenient method of changing values us-
ing the 3D digi-adjustors (
Step Activating flight phases
Once you have trimmed out the model accurately in
one flight phase (usually the HOVER phase), you may
wish to set up additional flight phases in order to opti-
mise the model for different flight situations (e.g.
CRUISE , ACRO ).
This is done by activating a new flight phase and copy-
ing the values from the first phase into the new, now
active one ( 18.4.). You can then adjust the transmit-
ter control settings - especially the collective pitch and
throttle curves - in Menu H Control (
settings of the TAIL and Gyro mixers (
ues which are marked with a small number ( 1 ... 4 ) can
be adjusted separately for each flight phase (
P5
P4
P3
Idle
(Throttle min. + Trim)
Throttle min.
11.2.2.).
14.), and the
15.). All val-
18.4.).
TIP: Speed regulators (governors)
If you wish to use a speed regulator with a glow-
powered model helicopter, i.e. a system which auto-
matically maintains a very constant system rotational
speed, the ROYALevo7 has a special function to offer:
Assign the function RPM to a vacant servo output (
16.2.); the speed regulator is connected to this receiver
output. In the Control menu you will now see the con-
trol "RPM". Here you can set a fixed value for the nomi-
nal rotational speed, separately for each flight phase (
14.1.8.). The speed regulator (i.e. the fixed value for the
regulator) can be switched off at any time using switch
"G". In this case the throttle servo is controlled in the
usual way via the throttle curve.
Before using the system be sure to read the information
in the unit's operating instructions.
20. The model templates
in detail
In the following sections you will find a detailed descrip-
tion of all model templates offered by your ROYALevo7.
Model templates enable you to set up a new model
quickly and very easily. Just follow our recommended
procedure:
19.2. Setting up a new fixed-wing model aircraft
19.3. Setting up a new model helicopter
In each template description you first find out which
types of model are suitable for that template.
In the first section (20.x.1.) you will see which transmit-
ter controls and switches are assigned. In the drawing
you will also see how the switches and controls must be
set before you switch the model on, i.e. the position of
maximum safety.
In the second section (20.x.2.) you will find a drawing
which shows the receiver outputs to which the servos
(speed controller, gyro etc.) have to be connected. The
servo sequence varies according to the servo configura-
tion which you selected when you set up a new mem-
ory.
The third section (20.x.3.) contains information about
the mixer facilities offered by the template in question.
Page 58