Rabe ADLER XT100 Notice Originale page 6

7 -Always ensure that universal drive shaft guards
are immobilized in rotation using the specially
provided chains.
8 -Before engaging power take-off , ensure that the
speed selected and the direction of rotation of the
power take-off comply with the manufacturer's
instructions.
9 -Before engaging power take-off , ensure that no
persons or animals are close to the machine.
10 -Disengage power take-off when the
universal drive shaft angle limits laid down by the
manufacturer are in danger of being exceeded.
11 -Caution! When power take-off has been
disengaged, moving parts may continue to rotate
for a few moments. Do not approach until they have
reached a complete standstill.
12 -On removal from the machine, rest the universal
drive shafts on the specially provided supports.
13 -After disconnecting the universal drive shafts
from the power take-off , the protective cap should be
fi tted to the power take-off .
14 -Damaged power take-off and universal drive
shaft guards must be replaced immediately.
HYdRaULIc cIRcUIt
1 -Caution! The hydraulic circuit is pressurized.
2 -When fi tting hydraulic motors or cylinders,
ensure that the circuits are connected correctly in
accordance with the manufacturer's guidelines.
3 -Before fi tting a hose to the tractor's hydraulic
circuit, ensure that the tractor-side and machine-side
circuits are not pressurized.
4 -The user of the machine is strongly recommended
to identify the hydraulic couplings between the
tractor and the machine in order to avoid wrong
connection. Caution! There is a danger of reversing
the functions (for example: raise/lower).
5 -Check hydraulic hoses once a year:
. Damage to the outer surface
. Porosity of the outer surface
. Deformation with and without pressure
. State of the fi ttings and seals
The maximum working life for hoses is 6 years.
When replacing them, ensure that only hoses with
the specifi cations and grade recommended by the
machine manufacturer are used.
6 -When a leak is found, all necessary precautions
should be taken to avoid accidents.
danGeR
Rotating disc
1
Projection of fertilizer
Hydraulic pressure
2
Drive shaft
Risk of crushing or pinching!
3
Do not stand on the ladder or
4
deck
Check that the booms are
5
properly locked in place.
6
7 -Pressurized liquid, particularly hydraulic circuit
oil, may cause serious injury if it comes into contact
with the skin. If the case of injury, consult a doctor
immediately. There is a risk of infection.
8 -Before any operation on the hydraulic circuit,
lower the machine, release the pressure from the
circuit, turn off the engine and remove the key from
the ignition.
MaIntenance
1 -Before commencing any maintenance, servicing
or repair work, or before attempting to locate the
source of a breakdown or fault, it is essential that the
power take-off is disengaged, the engine turned off
and the key removed from the ignition.
2 -Check regularly that nuts and screws are not
loose. Tighten if necessary.
3 -Before carrying out maintenance work on a raised
machine, prop it up using appropriate means of
support.
4 -When replacing a working part (fertilizer spreader
blade or seed drill coulter), wear protective gloves
and only use appropriate tools.
5 -To protect the environment, it is forbidden to
throw away oil, grease or fi lters of any kind. Give
them to specialist recycling fi rms.
6 -Before operating on the electric circuit, disconnect
the power source.
7 -Protective devices likely to be exposed to wear
and tear should be checked regularly. Replace them
immediately if they are damaged.
8 -Spare parts should comply with the standards and
specifi cations laid down by the manufacturer. Only
use the manufacturer's original parts.
9 -Before commencing any electric welding work
on the tractor or the towed machine, disconnect the
alternator and battery cables.
10 -Repairs aff ecting parts under stress or pressure
(springs, pressure accumulators, etc.) should be
carried out by suitably qualifi ed engineers with
special tools.
11 -All machine components, as well as the
protective devices, which are in an advanced state of
corrosion, should be replaced immediately.
4
1
5
2
3