Stryker S3 MedSurg Bed with StayPut Frame Mode D'emploi page 7

W W a a r r n n i i n n g g / / C C a a u u t t i i o o n n / / N N o o t t e e D D e e f f i i n n i i t t i i o o n n
The words W W A A R R N N I I N N G G , C C A A U U T T I I O O N N , and N N O O T T E E carry special meanings and should be carefully reviewed.
W W A A R R N N I I N N G G
Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.
C C A A U U T T I I O O N N
Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the
user or patient or damage to the product or other property. This includes special care necessary for the safe and effective
use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse.
N N o o t t e e - - Provides special information to make maintenance easier or important instructions clearer.
S S u u m m m m a a r r y y o o f f s s a a f f e e t t y y p p r r e e c c a a u u t t i i o o n n s s
Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.
W W A A R R N N I I N N G G
• Always plug the product directly into a grounded, hospital grade wall outlet. You can only achieve grounding reliability
when you use a hospital grade wall outlet. This product is equipped with a hospital-grade plug for protection against
electric shock hazard.
• Always use a Stryker supplied interface cable. Use of any other cable may cause the bed to not function as intended,
which may result in patient or user injury.
• Always associate or map the i i B B e e d d L L o o c c a a t t o o r r to the room or location to provide accurate location information. If you move
an i i B B e e d d L L o o c c a a t t o o r r after it has been installed and mapped, you must remap to the new room or location.
• Always apply the brakes when a patient is getting into or out of the product to avoid instability.
• Always apply the brakes when the patient is unattended.
• Do not apply the brakes to slow or stop the product while it is in motion.
• Always lock the siderails in the full up position with the sleep surface horizontal in the lowest position when you transport
the product with a patient.
• Always unplug the power cord before you transport the product.
• Always release the brakes before you transport the product. Do not transport the product with the brakes applied.
• Do not transport the product laterally after you apply the steer lock pedal. The product cannot swivel when you transport
with steer lock.
• Always use caution when transporting the product with the motorized drive wheel. Injury to the patient, operator, or
others, or damage to the product or equipment could occur if the product collides with an obstacle.
• Always use caution when transporting the product through halls, doors, and elevators. Damage to the siderails or other
parts of the product could occur if the product collides with walls or door frames.
• Always put the motorized drive wheel in the neutral position and release the brakes before transporting the product
manually. Do not transport the product manually with the motorized drive wheel in drive as the product will be difficult to
transport and could injure the operator.
• Always follow patient monitoring protocol to avoid patient injury. Power save mode is active after one hour on battery
power and no motion release switch activation. Bed exit, scale, and motion functions will not operate while the product is
in power save mode.
• Only use retractable traction or fracture frames. Failure to use a retractable frame may result in injury to the patient and/
or damage the equipment.
• Always set the siderail position to make sure that a patient is safely in the product.
• Always lock the operator control panel and patient control panel when the patient is unattended.
• Always keep the siderails outside of the oxygen tent.
• Only use hospital-grade electric equipment consuming 10A or less with the auxiliary power outlet (option). The use of
standard electric equipment may bring the current leakage to a level unacceptable for hospital equipment.
3006-209-005 Rev AA.2 3 EN