Electrostatic Discharge (Esd) - Stryker S3 MedSurg Bed with StayPut Frame Mode D'emploi

R R e e c c o o m m m m e e n n d d e e d d s s e e p p a a r r a a t t i i o o n n s s d d i i s s t t a a n n c c e e s s b b e e t t w w e e e e n n p p o o r r t t a a b b l l e e a a n n d d m m o o b b i i l l e e R R F F c c o o m m m m u u n n i i c c a a t t i i o o n n e e q q u u i i p p m m e e n n t t a a n n d d t t h h e e 3 3 0 0 0 0 2 2
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer.
N N o o t t e e - - At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
N N o o t t e e - - These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
The 3002 S S 3 3 MedSurg bed is suitable for use in the electromagnetic environment specified below. The customer or the
user of the 3002 S S 3 3 MedSurg bed should assure that it is used in such an environment.
I I m m m m u u n n i i t t y y t t e e s s t t
Electrostatic Discharge
(ESD)
IEC 61000-4-2
Electrostatic fast transient/
burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, voltage
variations and short
interruptions on power
supply input lines
IEC 61000-4-11
3006-209-005 Rev AA.2
G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y
I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l
+6 kV contact
+8 kV air
+2 kV for power supply lines
+1 kV for input/ output lines
±8 kV lines to lines
±2 kV lines to earth
<5%U (>95% dip in U
T
for 0,5 cycle
40%U (60% dip in U
T
for 5 cycles
70%U (30% dip in U
T
for 25 cycles
<5% U (>95% dip in U
T
for 5 sec.
S S 3 3 M M e e d d S S u u r r g g b b e e d d
12
C C o o m m p p l l i i a a n n c c e e l l e e v v e e l l
+6 kV contact
+8 kV air
+2 kV for power supply lines
+1 kV for input/ output lines
±8 kV lines to lines
±2 kV lines to earth
) <5%U (>95% dip in U
T T
for 0,5 cycle
) 40%U (60% dip in U
T T
for 5 cycles
) 70%U (30% dip in U
T T
for 25 cycles
) <5% U (>95% dip in U
T T
for 5 sec.
12
E E l l e e c c t t r r o o m m a a g g n n e e t t i i c c
e e n n v v i i r r o o n n m m e e n n t t - - g g u u i i d d a a n n c c e e
Floors should be wood,
concrete, or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Main power quality should
be that of a typical
commercial or hospital
environment.
Main power quality should
be that of a typical
commercial or hospital
environment.
)
T
Main power quality should
be that of a typical
commercial or hospital
)
environment. If the user of
T
the 3002 S S 3 3 MedSurg bed
requires continued
operation during power
)
T
main interruptions, it is
recommended that the
device be powered from an
uninterrupted power supply
)
T
or a battery.
23
63 EN