Care Of Your Machine Replacing The Upper Knife; Cleaning Upper Knife Area - ELNA eXtend 264 Livret D'instructions

0.8 ~ 1.5 mm (3/64˝)
0.8 ~ 1.5 mm (3/64˝)
0.8 ~ 1.5 mm (3/64˝)
36
36
36
CARE OF YOUR MACHINE
CARE OF YOUR MACHINE
CARE OF YOUR MACHINE
Replacing the Upper Knife
CARE OF YOUR MACHINE
Replacing the Upper Knife
Replacing the Upper Knife
Replacing the Upper Knife
To remove:
To remove:
To remove:
To remove:
1. Turn off the power switch and unplug the machine.
1. Turn off the power switch and unplug the machine.
1. Turn off the power switch and unplug the machine.
z Turn off the power switch and unplug the machine.
2. Open the looper cover and side cover.
2. Open the looper cover and side cover.
2. Open the looper cover and side cover.
x Open the looper cover and side cover.
3. Deactivate the upper knife.
c Deactivate the upper knife.
3. Deactivate the upper knife.
3. Deactivate the upper knife.
v Remove the hexagonal bolt, and remove the upper 4. Remove the hexagonal bolt, and remove the
4. Remove the hexagonal bolt, and remove the
4. Remove the hexagonal bolt, and remove the
knife.
upper knife.
upper knife.
upper knife.
q Upper knife
Upper knife
Upper knife
w Hexagonal bolt
Upper knife
e Stopper pin Hexagonal bolt
Hexagonal bolt
Hexagonal bolt
r Lower knife
Stopper pin
Stopper pin
Stopper pin
Lower knife
Lower knife
Lower knife
To attach:
To attach:
To attach:
To attach:
1. Insert new upper knife into the groove of knife
1. Insert new upper knife into the groove of knife
1. Insert new upper knife into the groove of knife
z Insert new upper knife into the groove of knife holder
holder and stopper pin, then tighten the
holder and stopper pin, then tighten the
holder and stopper pin, then tighten the
and stopper pin, then tighten the hexagonal bolt
hexagonal bolt slightly.
hexagonal bolt slightly.
slightly.
hexagonal bolt slightly.
x Turn the upper knife holder to cutting position.
2. Turn the upper knife holder to cutting position.
2. Turn the upper knife holder to cutting position.
2. Turn the upper knife holder to cutting position.
c Turn the handwheel toward you until the upper knife
3. Turn the handwheel toward you until the upper
3. Turn the handwheel toward you until the upper
3. Turn the handwheel toward you until the upper
comes to its lowest position.
knife comes to its lowest position.
knife comes to its lowest position.
Loosen the hexagonal bolt, and adjust the position
knife comes to its lowest position.
Loosen the hexagonal bolt, and adjust the
of the upper knife so that the edge of the upper knife
Loosen the hexagonal bolt, and adjust the
Loosen the hexagonal bolt, and adjust the
overlaps 0.8 to 1.5 mm (3/64´´) from the edge of lower
position of the upper knife so that the edge of the
position of the upper knife so that the edge of the
position of the upper knife so that the edge of the
knife as illustrated.
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
Then tighten the hexagonal bolt firmly.
the edge of lower knife as illustrated.
the edge of lower knife as illustrated.
the edge of lower knife as illustrated.
v Close the looper cover and side cover.
Then tighten the hexagonal bolt firmly.
Then tighten the hexagonal bolt firmly.
Then tighten the hexagonal bolt firmly.
4. Close the looper cover and side cover.
4. Close the looper cover and side cover.
4. Close the looper cover and side cover.

Cleaning Upper Knife Area

Cleaning Upper Knife Area
Cleaning Upper Knife Area
Cleaning Upper Knife Area
z Turn off the power switch and unplug the machine.
1. Turn off the power switch and unplug the machine.
1. Turn off the power switch and unplug the machine.
1. Turn off the power switch and unplug the machine.
x Open the looper cover.
2. Open the looper cover.
2. Open the looper cover. Remove the waste pieces to the front with a lint brush
2. Open the looper cover.
or waste scraps. Remove the waste pieces to the front with a lint
Remove the waste pieces to the front with a lint
Remove the waste pieces to the front with a lint
brush or waste scraps.
brush or waste scraps.
brush or waste scraps.
* You may use a vacuum cleaner to clean the upper knife
area or feed dog.
You may use a vacum cleaner to clean the upper
You may use a vacum cleaner to clean the upper
You may use a vacum cleaner to clean the upper
knife area or feed dog.
knife area or feed dog.
* The lower knife will last over one year in normal use. knife area or feed dog.
However, if you run over a pin or a hard object, it may
be required to replace both upper and lower knives at The lower knife will last over one year in normal
The lower knife will last over one year in normal
The lower knife will last over one year in normal
the same time.
use. However, if you run over a pin or a hard
use. However, if you run over a pin or a hard
use. However, if you run over a pin or a hard
object, it may be required to replace both upper
object, it may be required to replace both upper
object, it may be required to replace both upper
and lower knives at the same time.
and lower knives at the same time.
and lower knives at the same time.
70