Changing Needle; Raising Or Lowering The Presser Foot - ELNA eXtend 264 Livret D'instructions

Table des Matières

Publicité

r
r
r
t
r
t
t
t
y
y
y
y
8
8
8
8
q
q
q
q
w
w
w
w
e
r
e
r
w
e
r
e
r
w
q
w
w
q
q
q
y
y
y
y

Changing Needle

Turn off the power switch and unplug the machine.
Turn off the power switch and unplug the machine.
Raise the needle to its highest position.
Turn off the power switch and unplug the machine.
Raise the needle to its highest position.
Then loosen the left or right needle clamp screw for the needle
Then loosen the left or right needle clamp screw for the
Raise the needle to its highest position.
Turn off the power switch and unplug the machine.
Turn off the power switch and unplug the machine.
you are going to remove.
needle you are going to remove.
Then loosen the left or right needle clamp screw for the
Raise the needle to its highest position.
q Needle clamp screw on the left
Raise the needle to its highest position.
w Needle clamp screw on the right
needle you are going to remove.
Then loosen the left or right needle clamp screw for the
Needle clamp screw on the left
Then loosen the left or right needle clamp screw for the
needle you are going to remove.
needle you are going to remove.
Needle clamp screw on the right
* Use HA-1SP #14 Needle or #11.
Needle clamp screw on the left
Needle clamp screw on the right
Needle clamp screw on the left
Needle clamp screw on the left
Use HA-1SP #14 Needle or #11.
Needle clamp screw on the right
Needle clamp screw on the right
Use HA-1SP #14 Needle or #11.
Use HA-1SP #14 Needle or #11.
Use HA-1SP #14 Needle or #11.
To attach the needle on the right :
To attach the needle on the right :
Insert a new needle into the needle clamp with the
flat side to the back until the top of the needle
To attach the needle on the right :
Insert a new needle into the needle clamp with the
To attach the needle on the right :
To attach the needle on the right :
touches the stopper pin, then tighten the needle
flat side to the back until the top of the needle
Insert a new needle into the needle clamp with the flat side to
Insert a new needle into the needle clamp with the
Insert a new needle into the needle clamp with the
clamp screw on the right.
the back until the top of the needle touches the stopper pin,
touches the stopper pin, then tighten the needle
flat side to the back until the top of the needle
flat side to the back until the top of the needle
then tighten the needle clamp screw on the right.
clamp screw on the right.
touches the stopper pin, then tighten the needle
touches the stopper pin, then tighten the needle
To attach the needle on the left :
clamp screw on the right.
To attach the needle on the left :
clamp screw on the right.
To attach the needle on the left :
Insert a new needle into the needle clamp with the
Insert a new needle into the needle clamp with the flat side to
the back until the top of the needle touches the edge of the
flat side to the back until the top of the needle
To attach the needle on the left :
Insert a new needle into the needle clamp with the
To attach the needle on the left :
needle bar, then tighten the needle clamp screw on the left.
touches the edge of the needle bar, then tighten the
flat side to the back until the top of the needle
Insert a new needle into the needle clamp with the
Insert a new needle into the needle clamp with the
needle clamp screw on the left.
* When the needles are set correctly, the left needle is
touches the edge of the needle bar, then tighten the
flat side to the back until the top of the needle
flat side to the back until the top of the needle
higher than the right one.
needle clamp screw on the left.
touches the edge of the needle bar, then tighten the
touches the edge of the needle bar, then tighten the
* Use HA-1SP #14 Needle or #11.
needle clamp screw on the left.
needle clamp screw on the left.
q Needle clamp
w Needle
e Needle stopper pin
Needle clamp
r Edge of needle bar
Needle
t Needle clamp screws
Needle clamp
y Flat side to the back
Needle stopper pin
Needle
Needle clamp
Needle clamp
Edge of needle bar
Needle stopper pin
Needle
* Do not use any needle which is bent or blunt.
Needle
Needle clamp screws
Edge of needle bar
Needle stopper pin
Needle stopper pin
Flat side to the back
Needle clamp screws
Edge of needle bar
Edge of needle bar
Flat side to the back
Needle clamp screws
Needle clamp screws
Flat side to the back
Flat side to the back
By raising or lowering the presser foot lifter, the

Raising or Lowering the Presser Foot

presser foot goes up or down.
By raising or lowering the presser foot lifter, the
By raising or lowering the presser foot lifter, the presser foot
presser foot goes up or down.
By raising or lowering the presser foot lifter, the
goes up or down.
By raising or lowering the presser foot lifter, the
except when threading the machine or test-
presser foot goes up or down.
presser foot goes up or down.
* While in operation, keep the presser foot lowered except
running without threads.
except when threading the machine or test-
when threading the machine or testrunning without
running without threads.
threads.
except when threading the machine or test-
except when threading the machine or test-
q Presser foot
Presser foot
running without threads.
running without threads.
w Presser foot lifter
Presser foot lifter
Presser foot
Presser foot lifter
Presser foot
Presser foot
Presser foot lifter
Presser foot lifter
12

Publicité

Table des Matières
loading

Table des Matières