Threading The Machine - ELNA eXtend 264 Livret D'instructions

14
14
14

Threading the Machine

The left illustration shows the completed threading conditions of
four threads.
The left illustration shows the completed threading
q Lower looper thread
The left illustration shows the completed threading
The left illustration shows the completed threading
w Upper looper thread
conditions of four threads.
conditions of four threads.
conditions of four threads.
e Right needle thread
r Left needle thread
Lower looper thread
t Thread guide
Lower looper thread
Lower looper thread
y Thread guide plate Upper looper thread
Upper looper thread
Upper looper thread
u Threading chart
Right needle thread
Right needle thread
Right needle thread
Left needle thread
The machine is pre-threaded to make threading easier.
Left needle thread
Left needle thread
Thread guide
Tie the end of a new thread to one of the pre-set threads, and
Thread guide
Thread guide
pull it to draw the new thread through the machine, following the
Thread guide plate
Thread guide plate
steps below.
Thread guide plate
Threading chart
Threading chart
Threading chart
* Turn off the power switch before threading the machine.
The machine is pre-threaded to make threading
The machine is pre-threaded to make threading
The machine is pre-threaded to make threading
easier.
easier.
easier.
Tie the end of a new thread to one of the pre-set
Tie the end of a new thread to one of the pre-set
Tie the end of a new thread to one of the pre-set
threads, and pull it to draw the new thread through
threads, and pull it to draw the new thread through
threads, and pull it to draw the new thread through
the machine, following the steps below.
the machine, following the steps below.
the machine, following the steps below.
* Turn off the power switch before threading the
* Turn off the power switch before threading the
* Turn off the power switch before threading the
machine.
machine.
machine.
1. Pull the threads from the spools and draw them
z Pull the threads from the spools and draw them
1. Pull the threads from the spools and draw them
1. Pull the threads from the spools and draw them
through the thread guides, then tie the thread
through the thread guides, then tie the thread ends
through the thread guides, then tie the thread
through the thread guides, then tie the thread
together.
ends together.
ends together.
ends together.
x Raise the presser foot, draw the threads until the knots
2. Raise the presser foot, draw the threads until the
2. Raise the presser foot, draw the threads until the
2. Raise the presser foot, draw the threads until the
are coming out from under the back of the presser
knots are coming out from under the back of the
knots are coming out from under the back of the
foot.
knots are coming out from under the back of the
presser foot.
presser foot.
c However, stop drawing the needle threads when the
presser foot.
3. However, stop drawing the needle threads when
knots reach just before the needle eye.
3. However, stop drawing the needle threads when
3. However, stop drawing the needle threads when
the knots reach just before the needle eye.
Cut the knots and thread the needle eye.
the knots reach just before the needle eye.
the knots reach just before the needle eye.
v Before starting sewing, clear the needle threads from
Cut the knots and thread the needle eye.
Cut the knots and thread the needle eye.
Cut the knots and thread the needle eye.
under the presser foot to make sure they are not
4. Before starting sewing, clear the needle threads
4. Before starting sewing, clear the needle threads
4. Before starting sewing, clear the needle threads
caught below the needle plate.
from under the presser foot to make sure they are
from under the presser foot to make sure they are
(Draw the needle threads in the direction A)
from under the presser foot to make sure they are
not caught below the needle plate.
Then pull out the threads to the back approximately 10
not caught below the needle plate.
not caught below the needle plate.
(Draw the needle threads in the direction A)
cm (4˝) away from the presser foot.
(Draw the needle threads in the direction A)
(Draw the needle threads in the direction A)
Then pull out the threads to the back approxi-
Lower the presser foot, and you are now ready to sew.
Then pull out the threads to the back approxi-
Then pull out the threads to the back approxi-
q Thread guide
mately 10 cm (4˝) away from the presser foot.
mately 10 cm (4˝) away from the presser foot.
mately 10 cm (4˝) away from the presser foot.
w Needle
Lower the presser foot, and you are now ready to
Lower the presser foot, and you are now ready to
Lower the presser foot, and you are now ready to
e Needle thread
sew.
sew.
r Presser foot
sew.
t Needle plate
Thread guide
Thread guide
Thread guide
• For re-threading the machine easily, start from the
Needle
Needle
Needle
lower looper, upper looper, right needle and left needle
Needle thread
threads.
Needle thread
Needle thread
Presser foot
Make sure to clear the needle threads out from below
Presser foot
Presser foot
the needle plate and draw them to the back and under Needle plate
Needle plate
Needle plate
the presser foot about 10 cm (4˝).
• For re-threading the machine easily, start from the
• For re-threading the machine easily, start from the
• For re-threading the machine easily, start from the
lower looper, upper looper, right needle and left
lower looper, upper looper, right needle and left
lower looper, upper looper, right needle and left
needle threads.
needle threads.
needle threads.
Make sure to clear the needle threads out from
Make sure to clear the needle threads out from
Make sure to clear the needle threads out from
below the needle plate and draw them to the
below the needle plate and draw them to the
below the needle plate and draw them to the
back and under the presser foot about 10 cm (4˝).
back and under the presser foot about 10 cm (4˝).
back and under the presser foot about 10 cm (4˝).
24